please dont rip this site

Microchip Cntdn CNTDWN_16F648NO4511_V4.ASM

  
;-------------------------------------------------------------------------;
;         	     A countdown timer for Psychoanalysis                     ;
;        ORIGINAL CODE April '99  Stan Ockers (ockers@anl.gov)            ;
;              Re-written by Brendon Archibald April 2007	              ;
;					Optimized for battery operation						  ;
; Moddified for use in the 16F648A uP - Use internal OSC No XTAL required ;
; My mods mostly have ;* comments original code is just ;				  ;
;       Modifications from original code include:						  ;
;	1\	Auto restart when reached zero.									  ;
;	2\	0 Digit blanking on least significant digits.					  ;
;	3\	Improved alarm noise by stopping interupts.						  ;
;	4\	Combined Set and Select switch functions (long press for Set)	  ;
;		Changed set routine, now start button increments digits and 	  ;
;	5\	select button locks in digits.									  ;
;	6\	Add power off feature combined with Start switch (long press)	  ;
;	7\	Add 2 min Auto shutdown timer when not counting.   				  ;
;   8\	Whist in power down uP sleeps till start button pressed			  ;
;	9\	Remove CD4511 from original design - Use retlw table for segments ;
;		Counts down from 0-99 min and 1-59 sec giving an alarm at 0       ;
; 			 	Initial counts are held in data EEPROM					  ;
;			 and can be selected and set with one button     	 		  ;
;                                                                         ;
;  *RAO-RA3 to bases of NPN transistors connect to cathode's of displays. ;
;  **RB0-RB6 to 7segment display digits a, b, c, d, e, f & g.   		  ;
;  * RA6 to Decimal Point Anode, Cathode to ground.					  ;
;	RB7 to start pushbutton used to start countdown and power off   .     ;
;  RA4 is an output whilst counting (Active low Open Drain)																	      ;
;  RA5 with pull-up resistor goes to PB to select from 15 starting counts ;
;  RA7 go's to piezo element via 100r resistor which gives an alarm.      ;
;-------------------------------------------------------------------------;

	list      p=16f648A           ; list directive to define processor
	#include <p16F648A.inc>       ; processor specific variable definitions

	errorlevel  -302              ; suppress message 302 from list file 

	__CONFIG   _CP_OFF & _DATA_CP_OFF & _LVP_OFF & _BOREN_OFF & _MCLRE_OFF & _WDT_OFF & _PWRTE_ON & _INTOSC_OSC_NOCLKOUT ;* Config's for MPLAB

;-------------------------------------------------------------------------;
;    Here we define our own personal registers and give them names        ;
;				*All moved to 16F6xx register locations*					  ;
;-------------------------------------------------------------------------;

SEC       EQU H'20'          ; this register holds the value of seconds
SEC10     EQU H'21'          ; holds value of 10's of seconds
MIN       EQU H'22'          ; holds value of minutes
MIN10     EQU H'23'          ; holds value of 10's of minutes
DIGCTR    EQU H'24'          ; 8 bit counter, only 2 lowest bits actually used
DIGIT     EQU H'25'          ; hold digit number to access table
INTCNT    EQU H'26'          ; counts # interrupts to determine when 1 sec up
FUDGE     EQU H'27'          ; allows slight adjustment every 7 interrupts
RUNFLG    EQU H'28'          ; bit 0 only, tells if countdown in progress 
SECNT     EQU H'29'          ; used in counting 50, 20 msec delays for 1 sec
CNTMSEC   EQU H'2A'          ; used in timing of milliseconds
ALARM     EQU H'2B'          ; bit 0 used as flag for when to alarm, ALSO SETS ALARM LENGTH
DISPSET   EQU H'2C'			 ;* bit 0 tells if in SETDISP and avoid bit blanking routine
NOISELP	  EQU H'2D'			 ;* USED FOR NOISE LOOP
BEEPS	  EQU H'2E'			 ;* USED FOR NUMBER OF BEEPS
AUTOFF	  EQU H'2F'			 ;* USED FOR AUTO OFF TIMER
BEEPDUR	  EQU H'30'			 ;* TEMP REG FOR BEEP DURATION
PORTA_TEMP	EQU H'31'		 ;* temporarily holds value of PORTA (MASKED)
DPLATCH		EQU H'32'		 ;* Holds latched value for DP
DPCNT		EQU H'33'

W_TEMP    EQU H'70'          ; temporarily holds value of W
STATUS_TEMP EQU H'71'        ; temporarily holds value of STATUS
OFFSET 		EQU H'72'		 ; hold offset of address in EEPROM
;-------------------------------------------------------------------------;
;    Here we give names to some numbers to make their use more clear      ;
;-------------------------------------------------------------------------;

   #DEFINE   START_PB	D'7'
   ;#DEFINE   SET_PB    D'6'	;** Delete use of set button on RB6
   #DEFINE   SELECT_PB	D'5'
   #DEFINE   DP			D'6'
   #DEFINE   RA7		D'7'
   #DEFINE   OUTPUT		D'4'
	;#DEFINE   RB5       D'5'	;** Not needed anymore


;-------------------------------------------------------------------------;
;         We set the start of code to orginate at location zero           ;
;-------------------------------------------------------------------------;

      ORG 0

            GOTO MAIN                  ; jump to the main routine
            NOP                        
            NOP                        
            NOP                        
            GOTO INTERRUPT             ; interrupt routine
;-------------------------------------------------------------------------;
;* Lookup table for 7segment display - replaces CD/HEF4511 display driver ;			  ;
;-------------------------------------------------------------------------;
SEGMENT     ADDWF PCL,f			     ; Bit table data for 7 segment digits
           	RETLW       B'00111111'  ; "0" 			 _a_
          	RETLW       B'00000110'  ; "1"		   f|   |b
           	RETLW       B'01011011'  ; "2"			|_g_|
          	RETLW       B'01001111'  ; "3"  	   e|	|c
          	RETLW       B'01100110'  ; "4"			|_d_|
          	RETLW       B'01101101'  ; "5"
          	RETLW       B'01111101'  ; "6"		   g to a
          	RETLW       B'00000111'  ; "7"
          	RETLW       B'01111111'  ; "8"
          	RETLW       B'01101111'  ; "9"
		  	RETLW       B'00000000'  ; "10 = blank"
			RETLW       B'01011100'  ; "11 = o"
			RETLW       B'01110001'  ; "12 = F"
			RETLW       B'01101101'  ; "13 = S"
			RETLW       B'01111001'  ; "14 = E"
			RETLW       B'01110000'  ; "15 = t"

;-------------------------------------------------------------------------;
;    This table is used to get a bit pattern that will turn on a digit    ;
;	 But only if next segment is not = 0 ie. O bit blanking				  ;
;	 Bit blanking not used if in SETDISP routine ie. DISPSET flag set	  ;
;	I know this can be done a better way but it worked so...			  ;
;-------------------------------------------------------------------------;
BITPAT2     ADDWF PCL,f                ;* get bit pattern for transistors - NO BIT BLANKING
			RETLW H'01'                ;* 0001
			RETLW H'02'				   ;* 0010
			RETLW H'04'                ;* 0100
			RETLW H'08'                ;* 1000

BLANK1		MOVF MIN10,f               ;* check MIN10 for zero
            BTFSS STATUS,Z             ;*							   
SHOWMIN		RETLW H'04'                ;* 0100
			MOVF MIN,f                 ;* check MIN for zero
            BTFSS STATUS,Z
			GOTO SHOWMIN			   ;* NOT 0 SO SHOW BIT
			GOTO BLANKDIG			   ;* MIN10 & MIN = 0 SO BLANK BIT

BLANK2		MOVF MIN10,f               ;* check MIN10 for zero
            BTFSS STATUS,Z
			GOTO SHOWSEC10
			MOVF MIN,f                 ;* check MIN for zero
            BTFSS STATUS,Z
SHOWSEC10	RETLW H'02'				   ;* 0010
			MOVF SEC10,f               ;* check SEC10 for zero
            BTFSS STATUS,Z
			GOTO SHOWSEC10			   ;* NOT 0 SO SHOW BIT
			GOTO BLANKDIG			   ;* MIN10 & MIN & SEC10 = 0 SO BLANK BIT
						   
BITPAT		BTFSC DISPSET,0			   ;* If in display set mode
			GOTO BITPAT2			   ;* then goto BITBAT2 otherwise continue
BITPAT1     ADDWF PCL,f                ;* get bit pattern for tranys, 0 turns segment on
SHOWSEC     RETLW H'01'                ;* 0001  Seconds never blank
            GOTO BLANK2                ;* SEC10 digit call - Blank if MIN & SEC10 = 0  
            GOTO BLANK1  			   ;* MIN10 digit call - Blank if MIN10 & MIN = 0 
            MOVF MIN10,f               ;* check MIN10 for zero
            BTFSS STATUS,Z             ;* If MIN10 = 0 Blank MIN10 Segment
SHOWMIN10	RETLW H'08'                ;* 1000  
BLANKDIG	RETLW H'00'                ;* 0000  Blank DIGITS if 0


;-------------------------------------------------------------------------;
;          Initialization routine sets up ports and timer                 ;
;-------------------------------------------------------------------------;

INIT        CLRF PORTB					; initialize PORTB
			CLRF PORTA					; initialize PORTA
			MOVLW H'07'					;* 16F6XX Specific - Turn comparators off and 
			MOVWF CMCON					;* enable pins for I/O functions
			BSF STATUS,RP0			   ; Select Bank1
			MOVLW B'10000000'          ; RB7 input all others outputs
            MOVWF TRISB                ;* Updated command from original code 
            MOVLW B'00100000'          ; Port RA5 input, others outputs
            MOVWF TRISA                ;* Updated command from original code                  
            MOVLW H'03'                ; prescaler on TMR0 and 1:16
            MOVWF OPTION_REG		   ;* write to OPTION register * Updated command
			BCF STATUS,RP0				; back to bank0
			MOVLW H'A0'                ; GIE & T0IE set T0IF cleared
            MOVWF INTCON               
            MOVLW H'F4'                ; initialize INTCNT
            MOVWF INTCNT               
            MOVLW H'06'                ; initialize FUDGE
            MOVWF FUDGE                
            CLRF OFFSET                ; initialize OFFSET
            MOVLW D'122'				;* initialize DPCNT 
			MOVWF DPCNT					;*
			BSF PORTA,OUTPUT		   ;* Set OUTPUT RA4 (Counting not in Progress)
			RETURN                     

;-------------------------------------------------------------------------;
;   This is the interrupt routine that is jumped to when TMR0 overflows   ;
;-------------------------------------------------------------------------;

INTERRUPT   MOVWF W_TEMP               ; save W
            SWAPF STATUS,W             ; save status
            MOVWF STATUS_TEMP          ; without changing flags
            BCF STATUS,RP0             ; return to bank 0
			BCF STATUS,RP1             ; return to bank 0 (shut ric up)
			MOVF PORTA,W				;* Save PORTA to w reg
			ANDLW B'11010000'			;* Mask off RA7,RA6 & RA4 (Outputs)
			MOVWF PORTA_TEMP			;* Save it for later
			MOVWF PORTA					;* Load it back into PORTA i.e. blank digits only
			INCF DIGCTR,f              ; next digit #
            MOVF DIGCTR,W              ; get it into W
            ANDLW H'03'                ; mask off 2 lowest bits
            MOVWF DIGIT                ; save it for later
            ADDLW H'20'                ;* point at register to display - moved due to 16F6XX
            MOVWF FSR                  ; use as pointer
            MOVF INDF,W                ; get value of reg pointed to into W
            CALL SEGMENT			   ;* Call segment lookup, return with value in w
			MOVWF PORTB                ; load w into portb - output to 7seg display's
            MOVF DIGIT,W               ; recall digit #
            CALL BITPAT                ;* get bit pattern, return with value in w
            ADDWF PORTA_TEMP,W		   ;*Add bit pattern to PORTA_TEMP keep value in W
			MOVWF PORTA                ; load w into porta  - i.e select segment/ETC
            DECFSZ DPCNT,f				;* Decrement and check if DPCNT = 0
			GOTO CONTINT				;* Not 0 so continue interrupt
			COMF DPLATCH,F				;* Is 0 so invert DPLATCH
			;MOVLW D'122'				;* Reset DPCNT
			;MOVWF DPCNT					;* 
CONTINT		DECFSZ INTCNT,f            ; finished 1 sec ?
            GOTO RESTORE               ; not yet, return and enable inter.
            CALL EVERYSEC              ; go to every second routine
            MOVLW H'F4'                ; reset INTCNT to normal value
            MOVWF INTCNT               
            DECFSZ FUDGE,f             ; time for fudge?
            GOTO RESTORE               ; not yet, continue on
            MOVLW H'06'                ; reset FUDGE to 6
            MOVWF FUDGE                
            INCF INTCNT,f              ; INTCNT to 245
RESTORE     SWAPF STATUS_TEMP,W        ; get original status back
            MOVWF STATUS               ; into status register
            SWAPF W_TEMP,f       	   ;* old no flags trick again
            SWAPF W_TEMP,W        	   ;* to restore W
            BCF INTCON,T0IF            ; clear the TMR0 interrupt flag
            RETFIE                     ; finished

;-------------------------------------------------------------------------;
;       This routine is called by the interrupt routine every second      ;
;-------------------------------------------------------------------------;

EVERYSEC    BTFSS RUNFLG,0             ; return if runflg not set
            RETURN                     
            BSF DPLATCH,0
			MOVLW D'122'				;* Reset DPCNT
			MOVWF DPCNT	
			DECF SEC,f                 ; decrement seconds digit
            INCFSZ SEC,W               ; test for underflow
            GOTO CKZERO                
            MOVLW H'09'                
            MOVWF SEC                  ; reset sec to 9
            DECF SEC10,f               ; decrement SEC10
            INCFSZ SEC10,W             ; check underflow
            GOTO CKZERO                
            MOVLW H'05'                  
            MOVWF SEC10                ; reset SEC10 to 5                
            DECF MIN,f                 ; decrement MIN          
            INCFSZ MIN,W               ; check underflow               
            GOTO CKZERO                
            MOVLW H'09'              
            MOVWF MIN                  ; reset MIN to 9
            DECF MIN10,f               ; decrement MIN10
CKZERO      MOVF SEC,f                 ; test SEC for zero
            BTFSS STATUS,Z             
            RETURN                     
            MOVF SEC10,f               ; check SEC10 for zero
            BTFSS STATUS,Z             
            RETURN                     
            MOVF MIN,f                 ; check MIN for zero
            BTFSS STATUS,Z             
            RETURN                     
            MOVF MIN10,f               ; check MIN10 for zero
            BTFSS STATUS,Z             
            RETURN                     
            CLRF RUNFLG                ; stop the countdown
            BCF PORTA,DP			   ;* clear decimal point
			BSF ALARM, 0               ; set the alarm flag
            RETURN                     

;-------------------------------------------------------------------------;
;       This routine is called by the MAINLOOP to set or clear the DP     ;
;-------------------------------------------------------------------------;
DPSET		BTFSC DPLATCH,0				;* Test DPLATCH bit0
			GOTO DPOFF					;* If 0 clear decimal point
			BSF PORTA,DP				;* If 1 turn on decimal point
			RETURN
DPOFF		BCF PORTA,DP				;* TURN OFF decimal point
			RETURN

;-------------------------------------------------------------------------;
;          This is a routine to read a byte from the data EEPROM          ;
;-------------------------------------------------------------------------;

READEE      BSF STATUS,RP0             ;* change to bank 1 - needed it
			MOVWF EEADR                ; set up eeprom address from W
            BSF EECON1,RD              ; set the read bit
            MOVF EEDATA,W              ; return value in W
            BCF STATUS,RP0             ;* back to bank 0
			RETURN                     

;-------------------------------------------------------------------------;
;         This routine fills the display registers from data EEPROM       ;
;-------------------------------------------------------------------------;

GETEE       MOVLW H'01'                ; EEprom location 1 +
            ADDWF OFFSET,W             ; offset from start 
            CALL READEE                ; into W
            MOVWF SEC                  ; into SEC register
            MOVLW H'02'                ; location 2 +
            ADDWF OFFSET,W             ; offset from start 
            CALL READEE                ; into W
            MOVWF SEC10                ; into SEC10 register
            MOVLW H'03'                ; location 3 +
            ADDWF OFFSET,W             ; offset from start 
            CALL READEE                ; into W
            MOVWF MIN                  ; into MIN register
            MOVLW H'04'                ; location 4 +
            ADDWF OFFSET,W             ; offset from start 
            CALL READEE                ; into W
            MOVWF MIN10                ; into MIN10 register
            RETURN                     

;-------------------------------------------------------------------------;
;              This routine writes a byte to data EEPROM                  ;
;-------------------------------------------------------------------------;
WRITECHK	BCF INTCON,GIE             ; clear GIE, disable interrupts
WRITEEE		BTFSC INTCON,GIE			;* Check if interrupt is disabled
			GOTO WRITECHK				;* If not disabled then do so
     		BSF STATUS,RP0             ; Change to bank1
			CLRF EECON1                
            BSF EECON1,WREN            ; enable write
    		MOVLW H'55'                ; magic sequence
            MOVWF EECON2               
            MOVLW H'AA'                  
            MOVWF EECON2               
            BSF EECON1,WR              ;* Write data to EEPROM
EELOOP      BTFSC EECON1,WR            ; wait for WR to go low i.e. Finished write
            GOTO EELOOP                ; not yet check again
            BCF EECON1,WREN            ;* Finished write, disable write enable
			BCF EECON1,EEIF            ; clear the interrupt flag
			BCF STATUS,RP0             ; return to bank0
            BSF INTCON, GIE            ; re-enable interrupts
			RETURN                     

;-------------------------------------------------------------------------;
;         This routine puts display registers into data EEPROM            ;
;-------------------------------------------------------------------------;

PUTEE       
			MOVF SEC,W                 
            BSF STATUS,RP0             ;* change to bank 1 to make it work
			MOVWF EEDATA               
            MOVLW H'01'                ; EEPROM location 1 +  
            ADDWF OFFSET,W             ; offset from start 
            MOVWF EEADR                
            CALL WRITEEE               ; put SEC digit into EEprom
            MOVF SEC10,W               
            BSF STATUS,RP0             ;* change to bank 1 to make it work  
			MOVWF EEDATA               
            MOVLW H'02'                ; EEPROM location 2 +  
            ADDWF OFFSET,W             ; offset from start 
            MOVWF EEADR                
            CALL WRITEEE               ; put SEC10 digit into EEprom
            MOVF MIN,W                 
            BSF STATUS,RP0             ;* change to bank 1 to make it work
			MOVWF EEDATA               
            MOVLW H'03'                ; EEPROM location 3 +  
            ADDWF OFFSET,W             ; offset from start 
            MOVWF EEADR                
            CALL WRITEEE               ; put MIN digit into EEprom
            MOVF MIN10,W               
            BSF STATUS,RP0             ;* change to bank 1 to make it work
			MOVWF EEDATA               
            MOVLW H'04'                ; EEPROM location 4 +  
            ADDWF OFFSET,W             ; offset from start 
            MOVWF EEADR                
            CALL WRITEEE               ; put MIN10 digit into EEprom
            RETURN                     

;-------------------------------------------------------------------------;
;         This is the main routine, the program starts here               ;
;-------------------------------------------------------------------------;

MAIN        CALL INIT                  ; set up ports etc.

;-------------------------------------------------------------------------;
;           We will return to this point when alarm is shut off.          ;
;-------------------------------------------------------------------------;

EE2D		CALL GETEE                 ; put eeprom in display regs.
            BCF RUNFLG, 0              ; clear run flag so no countdown
            BCF ALARM, 0               ; clear alarm flag
            BCF DISPSET,0			   ;* Initialise DISPSET flag (Enable Blanking)
			CALL WAITSTARTUP           ; wait till no switches pressed
            CALL WAITSELECT			   

;-------------------------------------------------------------------------;
;      This loop checks for either pushbutton and acts accordingly        ;
;    If however no switches are pressed for over a preset time call the   ;
;    SHUTOFF routine.													  ;
;-------------------------------------------------------------------------;
							; Setup AUTOFF TIMEOUT with interrupt gives 2 min delay
KEYCHKLOOP  MOVLW H'78'				;* 120 INTO AUTO OFF COUNTER
			MOVWF AUTOFF			;* 120 X .8SEC = 96sec BEFORE AUTO OFF
			MOVLW H'C8'				;* 200 INTO FIRST COUNTER
			MOVWF SECNT				;* 200 X 4MSEC = .8SEC or so
AUTOFFLOOP	MOVLW H'04'				;* 4MSEC DELAY
			CALL NMSEC
			BTFSS PORTB,START_PB       ; check for start pressed
            GOTO STARTLONG             ;* yes, check for long press
            BTFSS PORTA,SELECT_PB      ; No, check select pushbutton pressed
            GOTO SELLONG               ;* yes, check for long press.
            DECFSZ SECNT,f			   ;* no switches, decrement secnt, check for 0
			GOTO AUTOFFLOOP            ;* secnt not 0 so loop
			DECFSZ AUTOFF,f			   ;* secnt is 0, decrement autoff, check for 0
			GOTO AUTOFFLOOP			   ;* autoff not 0 so loop
			GOTO SHUTOFF			;* autoff is 0 so GOTO SHUTOFF
			
;-------------------------------------------------------------------------;
; Long Start press routine - If short press then skip to STARTCNT if long ;
; then blank display, stop interrupts and SLEEP till start pressed again. ;
; Upon Start press restart interupts and goto EE2D i.e. LIKE POWER UP
;-------------------------------------------------------------------------;
STARTLONG	MOVLW H'23'				   ;* 35 DELAYS 
			MOVWF SECNT				   ;* INTO SECNT REGISTER
STARTLOOP	CALL DLY20				   ;* CALL 20 MSEC DELAY
			BTFSC PORTB,START_PB       ;* Check, START BUTTON
			GOTO STARTCNT			   ;* IF IT IS (i.e SHORT PRESS) START COUNT
			DECFSZ SECNT,f			   ;* IF NOT DECREMENT SECNT AND CHECK IF IT REACHES ZERO
			GOTO STARTLOOP			   ;* IF IT HASNT GO AND CHECK BUTTON AGAIN
			CALL SHORTBEEP				;* Make a small noise
SHUTOFF		MOVLW H'0A'					;* IF THE START BUTTON IS STILL DOWN AFTER 35 LOOPS
			MOVWF MIN10  			   ;* Blank 10's of minutes,
			MOVLW H'0B'                ;* put a o in 
			MOVWF MIN                  ;* minutes
            MOVLW H'0C'				   ;* Put an "F" in
			MOVWF SEC10                ;* 10's of seconds
            MOVWF SEC                  ;* and seconds
			CALL WAITSTARTUP	
			MOVLW H'02'			    	;*  NUMBER OF BEEPS
			MOVWF BEEPS					;* LOAD 5 INTO BEEPS
			MOVLW H'02'					;* duration of beeps
			MOVWF BEEPDUR				;* ETC
			CLRF PORTB
			CALL BEEP					;* CALL BEEP
			MOVLW D'250'
			CALL NMSEC
			BCF INTCON, GIE				;* COME BACK FROM BEEP - DISABLE INTERUPTS
			CLRF PORTB
			MOVLW B'00010000'		;* select transistors - i.e. ALL OFF
			MOVWF PORTA				;*
			MOVLW H'08'                ;* Set INTCON RBIE - wake on PORTB
            MOVWF INTCON			   ;* Also GIE & T0IE & T0IF cleared
			CLRF TMR0                  ;* and clear timer 0 - SOUNDED LIKE A GOOD IDEA?
			SLEEP					   ;* Goto sleep, wait for button
			NOP						   ;* Required delay?
			;BCF INTCON, RBIF			;* DIDNT WORK AND DIDNT SEEM TO NEED IT??
			CALL SHORTBEEP				;* Make a small noise
			MOVLW H'A0'                ;* WAKE UP - GIE & T0IE set T0IF cleared
            MOVWF INTCON			   ;* i.e. restart interupts
			GOTO EE2D				   ;* Reload last eeprom & wait for start etc
;-------------------------------------------------------------------------;
;    If start key has been pressed then start countdown process,          ;
;    I initially released this code with only the setting of the          ;
;    run flag included.  If you think about it you must also reset        ;
;    TMR0 to zero.  TMR0 is free running and could have any value         ;
;    0-255 when the button in pressed. Also INTCNT has to be              ;
;    initialized because the previous count could have been cancelled.    ;
;-------------------------------------------------------------------------;
STARTCNT    CALL SHORTBEEP				;* Make a small noise
			CALL WAITSTARTUP           ; wait for release of start key
SUBSTART    MOVLW D'244'               ; reset INTCNT
            MOVWF INTCNT
            CLRF DPLATCH               ; reset DPLATCH
			CLRF TMR0                  ; and clear timer 0
            BSF RUNFLG, 0              ; start the countdown
			;BCF PORTA,OUTPUT		   ;* Clear OUTPUT RA4 (Counting in Progress)
;-------------------------------------------------------------------------;
;        Once started just loop looking for cancel or reaching 0000       ;
;-------------------------------------------------------------------------;

MAINLOOP    BTFSS PORTB,START_PB       ; countdown in progress, check start
            GOTO STOPCNT               ; Yes, Stop count
            CALL DPSET				   ;* No start switch, Set or clear decimal point
			BTFSS ALARM, 0             ; Reached 0000 yet?
            GOTO MAINLOOP              ; no, ALARM = 0 continue looping
			BCF INTCON, GIE            ; yes, ALARM = 1 disable interrupts
			BCF PORTA,DP			   ;* Clear decimal point
			BSF PORTA,OUTPUT		   ;* Set OUTPUT RA4 (Counting not in Progress)
			CALL SOUNDALARM            ; CALL SOUNDALARM routine and come back
            BSF INTCON, GIE            ; RE-ENABLE interrupts
			CALL GETEE                 ; put eeprom in display regs.
			BCF ALARM, 0               ; clear alarm flag
			GOTO SUBSTART			   ; ***Auto Restart triger point***

STOPCNT		BCF PORTA,DP			   ;* Clear decimal point
			;BSF PORTA,OUTPUT		   ;* Set OUTPUT RA4 (Counting not in Progress)
			CALL SHORTBEEP				;* Make a small noise
			GOTO EE2D
;-------------------------------------------------------------------------;
;    This code sounds the alarm 										  ;
;	Produces 1 long 1KHz tone at end of time out -  				      ;
;-------------------------------------------------------------------------;
			              
SOUNDALARM	MOVLW B'00111111'			;* LOAD a "0" ONTO SEGMENTS
			MOVWF PORTB					;* Load into PORTB
			MOVLW H'01'			    	;* NUMBER OF BEEPS
			MOVWF BEEPS
			MOVLW H'14'                ; ? delays of ? msec = ?sec or so into BEEPDUR reg
			MOVWF BEEPDUR
BEEP		BCF INTCON, GIE				;* DISABLE INTERUPTS T0 CLEAN UP SOUND
BEEP2		MOVFW BEEPDUR				;* LOAD BEEPDUR INTO W
			MOVWF ALARM				   	; LOAD W INTO ALARM REG - lazy and use ALARM reg for tone duration
NOISE		MOVLW H'FF'                	; 255 delays of 400 usec = 954usec or so
            MOVWF NOISELP              	; into NOISELP register
NOISELOOP	MOVF PORTA,W
			ANDLW B'11010000'
			XORLW B'10000000'			;* TOGGLE PORTA RA7 (Buzzer)
			MOVWF PORTA
			MOVLW H'08'                ; delay 8x10=80 microseconds (Freq of buzz)
            CALL N10USEC
            INCF DIGCTR,f               ;* If RA7 is a 0 increment digit #
            MOVF DIGCTR,W               ;* get it into W
            ANDLW H'03'                 ;* mask off 2 lowest bits 
			CALL BITPAT2				;* get bit pattern for transistors
			ADDWF PORTA,f					;* As a result gives basic multiplex display
DIGDIS		DECFSZ NOISELP,f        ; finished  delay?
			GOTO NOISELOOP			;* NO - DO IT AGAIN
			DECFSZ ALARM,f			; Check alarm reg for 0, decrement if not 
			GOTO NOISE				;* and loop
			MOVLW B'00010000'		;* select transistors - i.e. ALL OFF
			MOVWF PORTA				;*
			MOVLW H'C8'				;* DELAY BETWEEN BEEPS
			CALL NMSEC				;*
			DECFSZ BEEPS,f
			GOTO BEEP2
STOPBEEP	BSF INTCON, GIE            ; RE-ENABLE interrupts
			RETURN
			

SHORTBEEP	MOVLW D'100'                ; 100 delays of 80usec = 8msec or so
            MOVWF NOISELP
BEEPLOOP	MOVLW B'10000000'			;* XOR (TOGGLE) RA7
			XORWF PORTA,1
			MOVLW H'08'                ; delay 8x10=80 microseconds (Freq of buzz)
            CALL N10USEC
			DECFSZ NOISELP,f           ; finished  delay?
			GOTO BEEPLOOP				;* NO - DO IT AGAIN
			BCF PORTA,RA7           ;* YES BEEP PROCESS FINISHED CLEAR SPEAKER PIN
			RETURN						;* GO BACK

			

;-------------------------------------------------------------------------;
;                    Wait for release of start button                     ;
;-------------------------------------------------------------------------;

WAITSTARTUP BTFSS PORTB,START_PB       ; wait for release
			GOTO WAITSTARTUP           ; not released yet
			CALL DLY20                 ; debounce release 
            BTFSS PORTB,START_PB       ; 2nd check, make sure released
            GOTO WAITSTARTUP           ; keep checking
           	RETURN


;-------------------------------------------------------------------------;
;                    Wait for release of select button                    ;
;-------------------------------------------------------------------------;

WAITSELECT  BTFSS PORTA,SELECT_PB      ; wait for release
            GOTO WAITSELECT            ; not yet
            CALL DLY20                 ; debounce release 
            BTFSS PORTA,SELECT_PB      ; 2nd check, make sure released
            GOTO WAITSELECT            ; keep checking
            RETURN

;-------------------------------------------------------------------------;
;       Routine to follow sets the countdown time digit by digit          ;
;-------------------------------------------------------------------------;

SETDISP2    BSF DISPSET, 0             ;* set the DISPSET flag - Disable bitblanking
			MOVLW H'0A'                ; put 10 in 
			MOVWF MIN10                ; 10's of minutes
			MOVLW D'13'                ; put S in
			MOVWF MIN                  ; minutes			
			MOVLW D'14'                ; put E in
			MOVWF SEC10                ; 10's of seconds
			MOVLW D'15'                ; put t in
			MOVWF SEC                  ; seconds
			CALL SHORTBEEP				;* Make a small noise
			CALL WAITSELECT
			MOVLW H'0A'                ; put 10 in digits, (no display)
            MOVWF MIN                  ; minutes
            MOVWF SEC10                ; 10's of seconds
            MOVWF SEC                  ; seconds
STARTMIN10  CLRF  MIN10                ; 0 now in MIN10
			CALL WAITSELECT				;*
WAIT1		BTFSS PORTB,START_PB         ; set key pressed?
			GOTO MOREMIN10					;*
			BTFSS PORTA,SELECT_PB		;*
			GOTO SETMIN                ; yes MIN10 now set
			GOTO WAIT1
          
MOREMIN10	CALL SHORTBEEP				;* Make a small noise
			CALL WAITSTARTUP             ; wait for release of set key
            INCF MIN10,f               ; every  increment 10's MIN
            MOVLW H'0A'                ; reached 10?
            SUBWF MIN10,W              
            BTFSC STATUS,Z             ; Z set if reached 10
            GOTO STARTMIN10            ; start again with 0
            GOTO WAIT1					; Check buttons again

SETMIN	    CALL SHORTBEEP				;* Make a small noise
STARTMIN	CLRF MIN                   ; 0 into MIN
			CALL WAITSELECT	
WAIT2       BTFSS PORTB,START_PB		;*
			GOTO MOREMIN
			BTFSS PORTA,SELECT_PB		;*
			GOTO SETSEC10               ;* yes, finished with MIN
			GOTO WAIT2					; Check buttons again
            
MOREMIN		CALL SHORTBEEP				;* Make a small noise
			CALL WAITSTARTUP			;*
			INCF MIN,f                 ; every second increment MIN
            MOVLW H'0A'                ; reached 10?
            SUBWF MIN,W              
            BTFSC STATUS,Z             ; Z set if reached 10
            GOTO STARTMIN              ; put zero in if Z set
            GOTO WAIT2					; Check buttons again

SETSEC10	CALL SHORTBEEP				;* Make a small noise
STARTSEC10  CLRF SEC10                 ; 0 into SEC10
			CALL WAITSELECT				;*
WAIT3       BTFSS PORTB,START_PB		;*
			GOTO  MORESEC10                ;* yes quit incrementing
			BTFSS PORTA,SELECT_PB	 	;*
			GOTO SETSEC
			GOTO WAIT3                 ; continue wait
            
MORESEC10	CALL SHORTBEEP				;* Make a small noise
			CALL WAITSTARTUP			;*
			INCF SEC10,f               ; every second increment 10's SEC
            MOVLW H'06'                ; reached 6?
            SUBWF SEC10,W              
            BTFSC STATUS,Z             ; Z set if reached 6
            GOTO STARTSEC10            ; put zero in if Z set
            GOTO WAIT3					; Check buttons again

SETSEC		CALL SHORTBEEP				;* Make a small noise
STARTSEC	CLRF SEC
			CALL WAITSELECT
;-------------------------------------------------------------------------;
;                  Subroutine to avoid a set time of 0000 		          ;
;-------------------------------------------------------------------------;
			MOVF MIN10,f               ; check MIN10 for zero
            BTFSS STATUS,Z
			GOTO WAIT4			   ; Zero SEC reg and continue increment
			MOVF MIN,f                 ; check MIN for zero
            BTFSS STATUS,Z
			GOTO WAIT4			   ; Zero SEC reg and continue increment
			MOVF SEC10,f               ; check SEC10 for zero
            BTFSS STATUS,Z
			GOTO WAIT4			   ; Zero SEC reg and continue increment
			INCF SEC,f            	   ; Put 1 in SEC reg and continue increment 
			
WAIT4       BTFSS PORTB,START_PB		;*
			GOTO  MORESEC                ;* yes finished setting digits
			BTFSS PORTA,SELECT_PB		;*
			GOTO FINSET					;* yes finished setting digits
			GOTO WAIT4                 ; continue wait
            
MORESEC		CALL SHORTBEEP				;* Make a small noise
			CALL WAITSTARTUP			;*
			INCF SEC,f                 ;* increment SEC
            MOVLW H'0A'                ; reached 10?
            SUBWF SEC,W              
            BTFSC STATUS,Z             ; Z set if reached 10
            GOTO STARTSEC              ; Return to STARTSEC and start again
            GOTO WAIT4               ; Not 10 continue to increment

FINSET      CALL SHORTBEEP				;* Make a small noise
			MOVLW D'100'
			CALL NMSEC
			CALL SHORTBEEP				;* Make a small noise
			CALL WAITSELECT				;*
			CALL PUTEE                 ; put new digits into EEPROM
            BCF DISPSET, 0              ;* CLEAR the DISPSET flag - Enable bitblanking
			GOTO KEYCHKLOOP            ; start checking buttons again

;-------------------------------------------------------------------------;
;        Selects starting count by incrementing OFFSET		              ;
;-------------------------------------------------------------------------;
SELLONG		MOVLW H'23'				   ;* 700msec delay
			MOVWF SECNT				   ;*
SELLOOP		CALL DLY20				   ;*
			BTFSC PORTA,SELECT_PB      ;* wait for release
			GOTO SETSELECT			   ;* is released - (short press)
			DECFSZ SECNT,f		 	   ;* not released,  decrement SECNT check if 0
			GOTO SELLOOP			   ;* not 0 do it again
			GOTO SETDISP2			   ;* is 0 (long press)

SETSELECT   CALL SHORTBEEP
			MOVLW D'4'                 ; offset up 4
            ADDWF OFFSET,F             ; next offset position
            MOVLW D'60'                ; reached 16th yet?
            SUBWF OFFSET,W             ; will give zero if yes
            BTFSC STATUS,Z             ; skip if not 64
            CLRF  OFFSET               ; reset position to zero
            ;MOVLW 0                    ; EEPROM location   		   	(LEFT ALL THIS OUT)
            ;MOVWF EEADR                ; set up address    		  (BECAUSE IT DIDNT WORK)
            ;MOVF OFFSET,W              ; offset # into W   		   (AND I FIGURED, OFFSET)
            ;MOVWF EEDATA               ; set up data			 	(WASNT CHANGED AFTER POWER UP)
            ;BCF INTCON,GIE             ; clear GIE, disable interrupts  (AND IT WOULD WEAR)
            ;CALL WRITEEE               ; save # in location 0           (OUT EEPROM, AS I)
            ;BSF INTCON,GIE             ; re-enable interrupts           (WAS HAPPY TO HAVE)
            CALL GETEE                 ; get new start count into display  (LAST SETTING)
            CALL WAITSELECT            ; make sure select switch is up   (TO LEAVE IT OUT)
            GOTO KEYCHKLOOP            ; start checking buttons again

;-------------------------------------------------------------------------;
;  The following are various delay routines based on instruction length.  ;  
;  The instruction length is assumed to be 1 microsecond (4Mhz crystal).  ;
;-------------------------------------------------------------------------;

DLY20       MOVLW D'20'                   ; delay for 20 milliseconds
                ;*** N millisecond delay routine ***
NMSEC       MOVWF CNTMSEC              ; delay for N (in W) milliseconds
MSECLOOP    MOVLW D'248'               ; load takes 1 microsec
            CALL MICRO4                ; by itself CALL takes ...
                                       ; 2 + 247 X 4 + 3 + 2 = 995
            NOP                        ; 1 more microsec 
            DECFSZ CNTMSEC,f           ; 1 when skip not taken, else 2
            GOTO MSECLOOP              ; 2 here: total 1000 per msecloop
            RETURN                     ; final time through takes 999 to here
                                       ; overhead in and out ignored

                ;***  1 millisecond delay routine ***
ONEMSEC     MOVLW D'249'               ; 1 microsec for load W
                                       ; loops below take 248 X 4 + 3 = 995
MICRO4      ADDLW H'FF'                ; subtract 1 from 'W'
            BTFSS STATUS,Z             ; skip when you reach zero
            GOTO MICRO4                ; loops takes 4 microsec, 3 for last
            RETURN                     ; takes 2 microsec
                                       ; call + load  W + loops + return =
                                       ; 2 + 1 + 995 + 2 = 1000 microsec

				;*** N 10 microsecond delay routine ***
N10USEC     MOVWF CNTMSEC              ;* delay for N (in W) milliseconds
USECLOOP    MOVLW D'1'                 ;* load takes 1 microsec
			CALL MICRO4                ;* by itself CALL takes ...
                                       ;* 1 + 4 + 3 + 2 = 10
            DECFSZ CNTMSEC,f           ;* 1 when skip not taken, else 2
            GOTO USECLOOP              ;* 2 here: total 10 per usecloop
            RETURN                     ;* final time through takes 9 to here
                                       ;* overhead in and out ignored

;-------------------------------------------------------------------------;
;    Here we set up the initial values of the digits in data EEPROM       ;
;-------------------------------------------------------------------------;
           ORG H'2100'

          DE 0, 0, 0, 1, 0    ; 1st starting # (Should be 1 minute)
          DE  0, 0, 2, 0      ; 2nd starting # (Should be 2 minutes)
          DE  0, 0, 3, 0      ; 3rd starting # (Should be 3 minutes)
          DE  0, 0, 4, 0      ; 4th starting # (Should be 4 minutes)
          DE  0, 0, 5, 0      ; 5th starting # (Should be 5 minutes)
          DE  0, 0, 6, 0      ; 6th starting # 6 min
          DE  0, 0, 7, 0      ; 7th starting # 7 min
          DE  0, 0, 8, 0      ; 8th starting # 8 min
          DE  0, 0, 9, 0      ; 9th starting # 9 min
          DE  0, 0, 0, 1      ; 10th starting # 10 min
          DE  0, 0, 0, 2      ; 11th starting # 20 min
          DE  0, 0, 0, 3      ; 12th starting # 30 min
          DE  0, 0, 0, 4      ; 13th starting # 40 min
          DE  0, 0, 0, 5      ; 14th starting # 50 min
          DE  0, 0, 0, 6      ; 15th starting # 60 min

            END   


file: /Techref/microchip/cntdn/cntdwn_16F648no4511_V4.asm, 39KB, , updated: 2007/4/3 18:55, local time: 2024/3/28 03:18,
TOP NEW HELP FIND: 
34.226.141.207:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.massmind.org/Techref/microchip/cntdn/cntdwn_16F648no4511_V4.asm"> microchip cntdn cntdwn_16F648no4511_V4</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to www.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .