NOLIST ;============================================================================== ; : ; This program is available from: : ; : ; Rho Enterprises : ; 4100 W. Colfax Ave. : ; Box 33 : ; Denver, CO 80204 : ; : ; Phone: 720-359-1467 Email: info@rhoent.com : ; : ; http://www.rhoent.com/ : ; : ;============================================================================== ; ;SXDEFS.INC by Loren Blaney and Richard Ottosen 14-FEB-2000 ; ; ;Scenix SX Definitions for Microchip MPASM. ; ;REVISIONS: ;FEB-23-98, Released. ;MAR-21-98, Added ID label. Corrected XT & HS defs by swapping them. ; Removed ASCII defs. New STATUS defs. ;MAR-27-98, Added PAGEA, BANKA, FCALL, FGOTO, SKIP. ;APR-13-98, Added CSA, CSBE (etc.) macros. Enclose all arguments in parentheses. ; Indent macros. ;APR-23-98, Changed some comments. ;OCT-4-98, Removed "RADIX DEC", added processor type based on SX FUSEX bits, ; added Trim bits to FUSEX and other cleanup. R.O. ;OCT-14-98 BOSC defaults to a "1". ;NOV-4-98, Revised Pins, Trim bits and BOSC in DEVICE equates, removed some ; inversions. R.O. ;SEP-11-99, Added warnings and messages to BANK and PAGE macros. R.O. ;9-JAN-2000, Changed ID bytes to leave unused bits as ones. R.O. ;12-JAN-2000, Made variables in macros local. R.O. ;14-FEB-2000, Cleanup. R.O. ;Define special function registers: IND EQU 00h ;used for indirects thru fsr RTCC EQU 01h ;real time clock/counter PC EQU 02h ;low 8 bits of PC STATUS EQU 03h ;status bits FSR EQU 04h ;file select register RA EQU 05h ;I/O ports RB EQU 06h ;supports multi-input wake-up (MIWU) RC EQU 07h ;Define STATUS register bits: C EQU 0 ;carry DC EQU 1 ;digit carry Z EQU 2 ;zero PD EQU 3 ;sleep power down (true low) TO EQU 4 ;watchdog time out (true low) PA0 EQU 5 ;page select (LSB) PA1 EQU 6 ;page select PA2 EQU 7 ;page select (MSB) ;Define port control registers: TRISX EQU 0Fh ;tristate (1=input, 0=output) PLP EQU 0Eh ;pullup (1=none, 0=20k) LVL EQU 0Dh ;level (1=TTL, 0=CMOS) ST EQU 0Ch ;Schmitt trigger (1=disabled, 0=enabled) WKEN EQU 0Bh ;wake up (1=disabled, 0=enabled) WKED EQU 0Ah ;wake up edge (1=falling, 0=rising) WKPND EQU 09h ;wake up pending (1=pending, 0=none) CMP EQU 08h ;comparator bit: 0=result, 6=output, 7=enabled ;Define device symbols for configuration words (FUSE & FUSEX): OSCRC EQU b'00' ;external RC network (default, inverted) OSCHS EQU b'01' ;high speed external crystal/resonator OSCXT EQU b'10' ;normal external crystal/resonator OSCLP EQU b'11' ;low power external crystal/resonator WATCHDOG EQU 1 << 2 ;watchdog timer enabled ; default to disabled PROTECT EQU 1 << 3 ;code protect enabled (inverted) ; default is to disable code protect OSC4MHZ EQU b'1000' << 4 ;internal 4MHz OSC2MHZ EQU b'1001' << 4 ;internal 2MHz OSC1MHZ EQU b'1010' << 4 ;internal 1MHz OSC500KHZ EQU b'1011' << 4 ;internal 500KHz OSC250KHZ EQU b'1100' << 4 ;internal 250KHz OSC125KHZ EQU b'1101' << 4 ;internal 125KHz OSC62KHZ EQU b'1110' << 4 ;internal 62.5KHz OSC31KHZ EQU b'1111' << 4 ;internal 31.25KHz STACKX EQU 1 << d'8' ;stack is extended to 8 levels (inverted) ; default to 2 levels OPTIONX EQU 1 << d'9' ;extend option register to 8 bits (inverted) ; default to 6 bits SYNC EQU 1 << d'10' ;input syncing enabled (inverted) ; default to disabled TURBO EQU 1 << d'11' ;turbo mode enabled (inverted) ; default to disabled PAGES1 EQU b'00' << d'12' ;default PAGES2 EQU b'01' << d'12' PAGES4 EQU b'10' << d'12' PAGES8 EQU b'11' << d'12' BANKS1 EQU b'00' << d'14' ;default BANKS2 EQU b'01' << d'14' BANKS4 EQU b'10' << d'14' BANKS8 EQU b'11' << d'14' BOR40 EQU b'11' << d'16' ;4.0V brownout reset BOR25 EQU b'10' << d'16' ;2.5 BOR13 EQU b'01' << d'16' ;1.3 ;BOR00 EQU b'00' << d'16' ;disabled (default, inverted) CARRYX EQU 1 << d'18' ;ADDWF & SUBWF use carry input (inverted) ; default is to ignore carry in PRE7 EQU 1 << d'19' ;for changing the preset FUSEX bit 7 (inverted) ; default is no change ;for modifying factory IRC calibration TRIM0 EQU b'0000' << d'20' ;highest frequency TRIM3 EQU b'0001' << d'20' ; TRIM6 EQU b'0010' << d'20' ; TRIM9 EQU b'0011' << d'20' ; about 3% per step TRIM12 EQU b'1000' << d'20' ; TRIM15 EQU b'1001' << d'20' ; TRIM18 EQU b'1010' << d'20' ; TRIM21 EQU b'1011' << d'20' ;lowest frequency (default) PINS18 EQU b'0' << d'22' ;default to 18 pin PINS28 EQU b'1' << d'22' _INVERT EQU 0F0F8Bh ;the default looks like a PIC16C54 _DEVICE SET DEVICE ^ _INVERT _FUSE SET _DEVICE & 0FFFh _FUSEX SET _DEVICE >> d'12' ;Select a Microchip processor enough like the Scenix processor to satisfy the ; assembler PROCESSOR 16C57 ;select a default Microchip processor _PINS SET (_FUSEX & 0400h) >> d'10' _ROM SET _FUSEX & 003h ERRORLEVEL -223 ;processor type change is OK IF (_PINS == 00h) && (_ROM == 00h) ;18 pin, 512 words LIST PROCESSOR 16C54 ; "SX18AA" NOLIST ENDIF IF (_PINS == 01h) && (_ROM == 00h) ;28 pin, 512 words LIST PROCESSOR 16C55 ; "SX28AA" NOLIST ENDIF IF (_PINS == 00h) && (_ROM == 01h) ;18 pin, 1K words LIST PROCESSOR 16C56 ; "SX18AB" NOLIST ENDIF IF (_PINS == 01h) && (_ROM == 02h) ;28 pin, 2K words LIST PROCESSOR 16C57 ; "SX28AC" NOLIST ENDIF IF (_PINS == 00h) && (_ROM == 02h) ;18 pin, 2K words LIST PROCESSOR 16C58A ; "SX18AC" NOLIST ENDIF ERRORLEVEL +223 ;flag the processor type being changed ;Define macros for new Scenix instructions: __NowBank SET 0 ;Default to bank 0 for both past and present __LastBank SET 0 ; bank (like the H/W should but doesn't) __NowPage SET 7 ;Default to top page for both __LastPage SET 7 ; past and present page (like the H/W does) IREAD MACRO DATA 41h ;IREAD ;move instruction at (MODE:W) to MODE:W ENDM MOVMW MACRO DATA 42h ;MOVMW ;move MODE register to W register ENDM MOVWM MACRO DATA 43h ;MOVWM ;move W register to MODE register ENDM RET MACRO DATA 0Ch ;RET ;return without destroying W register ENDM RETP MACRO __NowPage SET __LastPage ;This does not work for routines called ; from the same page and more than one page ??? DATA 0Dh ;RETP ;RET & write return addr bits 10:9 into PA1:PA0 ENDM RETI MACRO DATA 0Eh ;RETI ;return from interrupt (pull W, STATUS, FSR, PC) ENDM RETIW MACRO DATA 0Fh ;RETIW ;return from interrupt and add W to RTCC ENDM PAGEX MACRO X ;(MPASM already uses "PAGE") NOLIST LOCAL _X _X SET X IF (_X)&0FFFFFFF8h ERROR "page > 7" ENDIF ;*** IF _X == __NowPage ;*** MESSG "Page was not changed" ;*** ENDIF ;*** IF _X != __LastPage ;*** MESSG "Page was not restored" ;*** ENDIF __LastPage SET __NowPage __NowPage SET _X LIST DATA 10h | (_X) ;PAGE--write N into bits PA2:PA0 (N = 0-7) ENDM PAGEA MACRO A ;(MPASM already uses "PAGE") NOLIST LOCAL _A _A SET A ;*** IF ((_A)>>9) == __NowPage ;*** MESSG "Page was not changed" ;*** ENDIF ;*** IF ((_A)>>9) != __LastPage ;*** MESSG "Page was not restored" ;*** ENDIF __LastPage SET __NowPage __NowPage SET ((_A)>>9) LIST DATA 10h|((_A)>>d'9') ;PAGE--write bits A12:A10 into PA2:PA0 ENDM BANKX MACRO X ;(MPASM already uses "BANK") NOLIST LOCAL _X _X SET X IF (_X)&0FFFFFFF8h ERROR "bank > 7" ENDIF IF _X == __NowBank MESSG "Bank was not changed" ENDIF IF _X != __LastBank MESSG "Bank was not restored" ENDIF __LastBank SET __NowBank __NowBank SET _X LIST DATA 18h|(_X) ;BANK ;write N into bits FSR7:FSR5 (N = 0-7) ENDM BANKA MACRO A ;(MPASM already uses "BANK") NOLIST LOCAL _A _A SET A IF ((_A)>>5) == __NowBank MESSG "Bank was not changed" ENDIF IF ((_A)>>5) != __LastBank MESSG "Bank was not restored" ENDIF __LastBank SET __NowBank __NowBank SET ((_A)>>5) LIST DATA 18h|((_A)>>5) ;BANK--write bits A7:A5 into FSR7:FSR5 ENDM MODE MACRO N NOLIST LOCAL _N _N SET N IF (_N)&0FFFFFFF0h ERROR "mode > 0Fh" ENDIF LIST DATA 50h|(_N) ;MODE ;write N into MODE register (N = 0-F) ENDM ;Define macros for SxSim simulator instructions: PRINTX MACRO DATA 01h ;PRINT ;simulator instruction: print byte in W ENDM INPUTX MACRO DATA 0Ah ;INPUT ;simulator instruction: W gets ASCII keystroke ENDM OUTPUTX MACRO DATA 0Bh ;OUTPUT ;simulator instruction: display ASCII char in W ENDM ;Define some basic macros: FGOTO MACRO A ;(MPASM already uses "LGOTO") NOLIST LOCAL _A _A SET A ERRORLEVEL -306 ;don't display "crossing page boundary" message LIST DATA 10h|((_A)>>d'9') ;PAGE--write bits A12:A10 into PA2:PA0 GOTO (_A)&1FFh ERRORLEVEL +306 ;restore "crossing page boundary" message ENDM FCALL MACRO A ;(MPASM already uses "LCALL") NOLIST LOCAL _A _A SET A ERRORLEVEL -306 ;don't display "crossing page boundary" message LIST DATA 10h|((_A)>>d'9') ;PAGE--write bits A12:A10 into PA2:PA0 CALL (_A)&1FFh ERRORLEVEL +306 ;restore "crossing page boundary" message ENDM ;(don't replace 1FFh with 0FFh) SKIP MACRO ;in turbo mode this saves one cycle over a GOTO NOLIST IF $&1 ;odd location LIST BTFSC PC,0 ;always skips NOLIST ELSE ;even location LIST BTFSS PC,0 ;always skips NOLIST ENDIF LIST ENDM CSA MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVF _X,W ;compare arg1 to arg2 and skip if above SUBWF _Y,W BTFSC STATUS,C ENDM CSA# MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVLW (_Y)^0FFh ;compare arg1 to literal and skip if above ADDWF _X,W BTFSS STATUS,C ENDM CSAE MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVF _Y,W ;compare arg1 to arg2 and skip if above or equal SUBWF _X,W BTFSS STATUS,C ENDM CSAE# MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVLW _Y ;compare arg1 to lit. and skip if above or equal SUBWF _X,W BTFSS STATUS,C ENDM CSB MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVF _Y,W ;compare arg1 to arg2 and skip if below SUBWF _X,W BTFSC STATUS,C ENDM CSB# MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVLW _Y ;compare arg1 to literal and skip if below SUBWF _X,W BTFSC STATUS,C ENDM CSBE MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVF _X,W ;compare arg1 to arg2 and skip if below or equal SUBWF _Y,W BTFSS STATUS,C ENDM CSBE# MACRO X,Y NOLIST LOCAL _X,_Y _X SET X _Y SET Y LIST MOVLW (_Y)^0FFh ;compare arg1 to lit. and skip if below or equal ADDWF _X,W BTFSC STATUS,C ENDM ;Define macro for ID label. Example: ; ID 'S', 'X', '-', 'D', 'e', 'm', 'o', ' ' ID MACRO A,B,C,D,E,F,G,H ;set up ID label NOLIST LOCAL _A,_B,_C,_D,_E,_F,_G,_H _A SET A _B SET B _C SET C _D SET D _E SET E _F SET F _G SET G _H SET H ERRORLEVEL -220 ;don't display "address exceeds range" warning ORG 1000h ;*** DATA (_A>>4)&0Fh, A&0Fh ;Unused bits are cleared ; DATA (_B>>4)&0Fh, B&0Fh ; DATA (_C>>4)&0Fh, C&0Fh ; DATA (_D>>4)&0Fh, D&0Fh ; DATA (_E>>4)&0Fh, E&0Fh ; DATA (_F>>4)&0Fh, F&0Fh ; DATA (_G>>4)&0Fh, G&0Fh ;*** DATA (_H>>4)&0Fh, H&0Fh DATA (_A>>4)|0FF0h, A|0FF0h ;Unused bits are set DATA (_B>>4)|0FF0h, B|0FF0h DATA (_C>>4)|0FF0h, C|0FF0h DATA (_D>>4)|0FF0h, D|0FF0h DATA (_E>>4)|0FF0h, E|0FF0h DATA (_F>>4)|0FF0h, F|0FF0h DATA (_G>>4)|0FF0h, G|0FF0h DATA (_H>>4)|0FF0h, H|0FF0h ERRORLEVEL +220 ;restore warning message ORG 0 LIST ENDM ERRORLEVEL -220 ;don't display "address exceeds range" warning ORG 1010h LIST DATA _FUSE ;configuration bits (TURBO, SYNC, OPTIONX, etc.) DATA _FUSEX ; (PINS, CARRYX, BOR40, BANKS, PAGES) NOLIST ERRORLEVEL +220 ;restore warning message ORG 0 LIST
Comments:
file: /Techref/scenix/sxdefs_inc.htm, 13KB, , updated: 2003/11/14 09:37, local time: 2024/10/12 01:28,
98.84.18.52:LOG IN ©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://www.massmind.org/Techref/scenix/sxdefs_inc.htm"> Scenix SX Definitions for Microchip MPASM</A> |
Did you find what you needed? |
Welcome to massmind.org! |
Welcome to www.massmind.org! |
.