please dont rip this site

Peter Verkaik's port of the MASM SERVID code to the SXKey

Code:

; SERVID - Serial video display using Ubicom SX microcontroller
; $Id  servid.asm,v 1.34 2001/01/31 07 25 31 eric Exp $
;****************************************************************
; SX-KEY source mnenomics for SX18 device by Peter Verkaik
; This port uses the same oscillator frequency as the original source
; so it should run directly for NTSC.
; Do not contact the authors of the original source about this conversion
; Instead contact me: peterverkaik@boselectro.nl
;****************************************************************
;
; Copyright 2000, 2001 Eric Smith <eric@brouhaha.com>
;
; Home page
;    http //www.brouhaha.com/ubicom/servid/
;
; This program is free software; you can redistribute it and/or modify
; it under the terms of the GNU General Public License version 2 as published
; by the Free Software Foundation.  Note that permission is not granted
; to redistribute this program under the terms of any other version of the
; General Public License.
;
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with this program; if not, write to the Free Software
; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
;
; NOTE   it is sometimes claimed that compliance with the GPL is
; awkward for commercial interests.  Licenses for non-GPL use of this
; program may be negotiated with the author.
;
; This program is written to be assembled with the GPASM assembler,
; version 0.8.14 or newer
;     http //gpasm.sourceforge.net/


; NOTE  there are references in this code to PAL and NTSC.  Technically
; those are color standards.  In most cases the references to PAL and NTSC
; are really intended to refer to 625/50 and 525/59.94 scanning, or (in
; non-interlaced mode) 312/25 and 262/29.97 scanning.

device		SX18L,oschs2,turbo,stackx_optionx,carryx	;sx device options
freq		42_954_545					;resonator frequency
id		'-SERVID-'					;code identification
reset		reset_entry					;set reset vector

;Features: 
;
;serial input at 1200 bps 8N1 (eight data bits, no parity, one stop bit), MSB ignored
;monochrome displayo of four lines of twenty characaters 
;1 volt peak-to-peak composite video ouptut into 75 ohm load 
;ASCII character set, 95 displayable characters 
;Subset of VT52 control characters and escape sequences 
;Automatic scrolling ( no extra "4" characters when scrolling ) 
;interlaced or non-interlaced video selectable by conditional assembly 
;approximate RS-170 timing (525/60) 
;approximate PAL timing (625/50) selectable by conditional assembly - maybe.
;PAL timing of an earlier version was only tested in a cursory fashion.
;Since then the line type table for PAL has been rewritten in an attempt to more
;closely meet PAL scanning specifications (e.g., 5 each equalization, vsync,
;equalization pulses per field). However, this newer code has not been tested
;in PAL mode at all. 
;This is a preliminary release. As such, it basically works,
;but there are some known bugs (and probably a lot of unknown ones): 
;
;some escape sequences are acting a bit flaky 
;Supported control codes: 
;
;    $00 Null
;    $07 Bell
;    $08 Backspace
;    $0A Line Feed
;    $0C Form Feed - clear display and home cursor
;    $0D Carriage Return
;    $1B Escape - introduce escape sequence
;    $7F Delete - ignored
;
;    All unrecognized control characters are ignored.
;Supported escape sequences: 
;
;    ESC A - Cursor Up    - wraparound rather than scroll
;    ESC B - Cursor Down  - wraparound rather than scroll
;    ESC C - Cursor Left
;    ESC D - Cursor Right
;
;    ESC H - Cursor Home
;    ESC I - Reverse Line Feed - may scroll
;    ESC J - Erase to End of Screen
;    ESC K - Erase to End of Line
;
;    ESC Y   - Direct cursor addressing, col and row offset by 32
;
;Customization: 
;
;SERVID is designed such that user application code may be added to (or replace)
;the serial character processing. In this release of the code there are 919 words
;of program memory free for a user application, and 21 bytes of RAM free.
;The video generation is entirely interrupt driven, so the user application code
;can run at non-interrupt time without any critical timing constraints. 
;
;Software Requirements: 
;
;As written, SERVID will only assemble with the GPASM assembler, version 0.8.14
;or newer. GPASM is Free Software: 
;http://gpasm.sourceforge.net/ 
;
;Hardware Requirements: 
;
;SERVID requires a processor clock of 42.954545 MHz (12 times the NTSC color burst frequency).
;Note that future versions of SERVID may change to a clock frequency of 57.272727 MHz
;(16 times the NTSC color burst frequency). Digikey offers suitable Epson oscillators
;which they program to customer spec; a suitable 8-pin DIP footprint (4 actual pin) part
;is part number SG-8002DC-PHB-ND. SERVID uses an 8-bit D/A converter on port B to generate
;the video output. A simple R-2R resistor ladder will suffice. 
;
;The serial input should be fed into port RA0. If a conventional EIA-232 receiver
;(MC1489, MAX232, or the like) is used, the variable ft_ser_noninv near the top of
;the servid.asm source file should be set to 0. For a non-inverting serial input
;(such as the crude resistor-only method, see the file SCHEMATIC), ft_ser_noninv
;should be set to 1. 
;
;Bill of Materials 
;All parts but the microcontroller are available from Digikey.
;Digikey part numbers are given except for the microcontroller,
;for which a Mouser part number is given.
;
;http://www.digikey.com/ 
;http://www.mouser.com/ 
;
;            Vendor     Distributor
;Q.  Vendor  Part       Part Number    Description
;--  ------  ---------  -------------  ----------------------------------------
; 1  Ubicom  SX18AC/DP  619-SX18AC/DP  microcontroller, 18-pin plastic DIP
; 1  Epson              SG-8002DC-PHB  preprogrammed oscillator, 42.9545454 MHz
; 1  CTS                761-3-R220     8 * 220 ohm DIP resistor network
; 2  CTS                770-103-R120   5 * 120 ohm SIP res. network, isolated
;
; 1                                    15 ohm 1/8 watt resistor
; 1                                    33K ohm 1/8 watt resistor
; 1                                    180K ohm 1/8 watt resistor
; 1                                    0.1 uF ceramic capacitor
;
; 1                                    BNC or RCA jack for video output
; 1                                    DB25 connector for serial input
; 1                                    5V regulated DC power supply
;
;Schematic 
;Schematic for SERVID
;$Id: SCHEMATIC,v 1.4 2001/01/04 23:52:55 eric Exp $
;
;Copyright 2001 Richard Ottosen
;
;
;                         +5V
;                          |
;          +---------------+
;          |               |
;       0.1 uF             |
;          |               |                                         1.25V p-p
;          |       ----------------                                  Video into
;          V      |                |                                 75 ohms
;                 |  Ubicom    /   |
;                 |  SX18AC   |  7 |--- 220 ohm ---+--------+--- 15 ohm --->
;                 |           |    |               |        |
;           +5V --| MCLR      |    |             120 ohm  120 ohm      +--->
;                 |           |    |               |        |          |
;----------       |           |  6 |--- 220 ohm ---+        |          |
;|42.954545 |     |           |    |               |        V	       V
;|   MHz    |-----| OSC1      |    |            120 ohm
;|Oscillator|     |           |    |               |
; ----------  NC--| OSC2      |  5 |--- 220 ohm ---+
;                 |           |    |               |
;                 |           |    |            120 ohm
;          +------| RTCC      |    |               |
;          |   	  |          /   4 |--- 220 ohm ---+
;          V      |         |      |               |
;                 | Port B <       |            120 ohm
;                 |         |      |               |
;             NC--| PA3      \   3 |--- 220 ohm ---+
;                 |           |    |               |
;             NC--| PA2       |    |            120 ohm
;                 |           |    |               |
;          +------| PA1       |  2 |--- 220 ohm ---+
;          |      |           |    |               |
;         --      |           |    |            120 ohm
;   piezo [] )))  |           |    |               |
;         --      |           |  1 |--- 220 ohm ---+
;          |      |           |    |               |
;          |      |           |    |            120 ohm
;          V      |           |    |               |
;IA-232           |           |  0 |--- 220 ohm ---+
;Input            |            \   |               |
;<----+--- 33K ---| PA0            |            120 ohm
;     |           |                |               |
;   180K           ----------------                |
;     |                    |                    120 ohm
;<----+                    |                       |
;     |                    |                       |
;     V                    V                       V
;---------------------------------------------------------------------------
; feature test switches
;---------------------------------------------------------------------------

ft_pal_video		equ	0	; 0 for NTSC 525/60, 1 for PAL 625/50
					; (approximate timing only)
					; (not well tested)

ft_interlace		equ	1	; 1 for interlaced video

ft_color		equ	0	; 1 for color burst (NTSC only)

ft_serial_input	        equ	1	; 1 for normal serial input,
					; 0 to omit (when replaced with user
					; application code)

ft_ser_noninv		equ	1	; 0 for "normal" TTL-level serial,
					;     mark = low, space = high
					; 1 for non-inverted serial (the
					; crude resistor-only method)
					;     mark = high, space = low

ft_splash 		equ	1	; 1 for splash screen

;==============================================================================
;
;        This program is available from
;
;               Rho Enterprises
;               4100 W. Colfax Ave.
;               Box 33
;               Denver, CO    80204
;
;        Phone  720-359-1467                   Email  info@rhoent.com
;
;                          http //www.rhoent.com/
;
;==============================================================================

;
;SXDEFS.INC by Loren Blaney and Richard Ottosen 14-FEB-2000
;
;Scenix SX Definitions for Microchip MPASM.
;
;REVISIONS
;FEB-23-98, Released.
;MAR-21-98, Added ID label. Corrected XT & HS defs by swapping them.
; Removed ASCII defs. New STATUS defs.
;MAR-27-98, Added PAGEA, BANKA, FCALL, FGOTO, SKIP.
;APR-13-98, Added CSA, CSBE (etc.) macros. Enclose all arguments in parentheses.
;  Indent macros.
;APR-23-98, Changed some comments.
;OCT-4-98, Removed "RADIX DEC", added processor type based on SX FUSEX bits,
;  added Trim bits to FUSEX and other cleanup.   R.O.
;OCT-14-98 BOSC defaults to a "1".
;NOV-4-98, Revised Pins, Trim bits and BOSC in DEVICE equates, removed some
;   inversions.  R.O.
;SEP-11-99, Added warnings and messages to BANK and PAGE macros.  R.O.
;9-JAN-2000, Changed ID bytes to leave unused bits as ones.  R.O.
;12-JAN-2000, Made variables in macros local.  R.O.
;14-FEB-2000, Cleanup.  R.O.

;Define special function registers
;INDF		equ	00h	;used for indirects thru fsr
;RTCC		equ	01h	;real time clock/counter
;PCL		equ	02h	;low 8 bits of PC
;STATUS		equ	03h	;status bits
;FSR		equ	04h	;file select register
;PORTA		equ	05h	;I/O ports
;PORTB		equ	06h	;supports multi-input wake-up (MIWU)
;PORTC		equ	07h

;Define STATUS register bits
CF		equ	0	;carry
DCF		equ	1	;digit carry
ZF		equ	2	;zero
PDF		equ	3	;sleep power down (true low)
TOF		equ	4	;watchdog time out (true low)
;PA0		equ	5	;page select (LSB)
;PA1		equ	6	;page select
;PA2		equ	7	;page select (MSB)

;Define port control registers
;TRISX		equ	0Fh	;tristate (1=input, 0=output)
;PLP		equ	0Eh	;pullup (1=none, 0=20k)
;LVL		equ	0Dh	;level (1=TTL, 0=CMOS)
;ST		equ	0Ch	;Schmitt trigger (1=disabled, 0=enabled)
;WKEN		equ	0Bh	;wake up (1=disabled, 0=enabled)
;WKED		equ	0Ah	;wake up edge (1=falling, 0=rising)
;WKPND		equ	09h	;wake up pending (1=pending, 0=none)
;CMP		equ	08h	;comparator bit  0=result, 6=output, 7=enabled

;Define device symbols for configuration words (FUSE & FUSEX)

;OSCRC		equ	%00	;external RC network (default, inverted)
;OSCHS		equ	%01	;high speed external crystal/resonator
;OSCXT		equ	%10	;normal external crystal/resonator
;OSCLP		equ	%11	;low power external crystal/resonator

;WATCHDOG	equ	1 << 2		;watchdog timer enabled
					; default to disabled
;PROTECT	equ	1 << 3		;code protect enabled (inverted)
					; default is to disable code protect

;OSC4MHZ	equ	%1000 << 4	;internal 4MHz
;OSC2MHZ	equ	%1001 << 4	;internal 2MHz
;OSC1MHZ	equ	%1010 << 4	;internal 1MHz
;OSC500KHZ	equ	%1011 << 4	;internal 500KHz
;OSC250KHZ	equ	%1100 << 4	;internal 250KHz
;OSC125KHZ	equ	%1101 << 4	;internal 125KHz
;OSC62KHZ	equ	%1110 << 4	;internal 62.5KHz
;OSC31KHZ	equ	%1111 << 4	;internal 31.25KHz

;STACKX		equ	1 << 8		;stack is extended to 8 levels (inverted)
					; default to 2 levels
;OPTIONX	equ	1 << 9		;extend option register to 8 bits (inverted)
					; default to 6 bits
;SYNC		equ	1 << 10		;input syncing enabled (inverted)
					; default to disabled
;TURBO		equ	1 << 11		;turbo mode enabled (inverted)
					; default to disabled

;PAGES1		equ	%00 << 12	;default
;PAGES2		equ	%01 << 12
;PAGES4		equ	%10 << 12
;PAGES8		equ	%11 << 12

;BANKS1		equ	%00 << 14	;default
;BANKS2		equ	%01 << 14
;BANKS4		equ	%10 << 14
;BANKS8		equ	%11 << 14

;BOR40		equ	%11 << 16	;4.0V brownout reset
;BOR25		equ	%10 << 16	;2.5
;BOR13		equ	%01 << 16	;1.3
;BOR00		equ	%00 << 16	;disabled (default, inverted)

;CARRYX		equ	1 << 18		;ADDWF & SUBWF use carry input (inverted)
					; default is to ignore carry in

;PRE7		equ	1 << 19		;for changing the preset FUSEX bit 7 (inverted)
					; default is no change

;for modifying factory IRC calibration
;TRIM0		equ	%0000 << 20	;highest frequency
;TRIM3		equ	%0001 << 20
;TRIM6		equ	%0010 << 20
;TRIM9		equ	%0011 << 20	; about 3% per step
;TRIM12		equ	%1000 << 20
;TRIM15		equ	%1001 << 20
;TRIM18		equ	%1010 << 20
;TRIM21		equ	%1011 << 20	;lowest frequency (default)

;PINS18		equ	%0 << 22	;default to 18 pin
;PINS28		equ	%1 << 22

int_off		equ	$c3		; RTCC internal clock, prescale by 16,
					; RTCC interrupt off, WDT disabled

int_on		equ	$83		; RTCC internal clock, prescale by 16,
					; RTCC interrupt on, WDT disabled

;---------------------------------------------------------------------------
; other includes
;---------------------------------------------------------------------------

; ASCII character definitions for serial video display
; $Id  ascii.inc,v 1.1 2001/01/03 20 06 47 eric Exp $
;
; Copyright 2000, 2001 Eric Smith <eric@brouhaha.com>
;
; This program is free software; you can redistribute it and/or modify
; it under the terms of the GNU General Public License version 2 as published
; by the Free Software Foundation.  Note that permission is not granted
; to redistribute this program under the terms of any other version of the
; General Public License.
;
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with this program; if not, write to the Free Software
; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
;
; Licenses for non-GPL use may be negotiated with the author.

asc_nul		equ	00h
asc_bel		equ	07h
asc_bs		equ	08h
asc_ht		equ	09h
asc_lf		equ	0ah
asc_ff		equ	0ch
asc_cr		equ	0dh
asc_so		equ	0eh
asc_si		equ	0fh
asc_esc		equ	1ah
asc_del		equ	7fh

;---------------------------------------------------------------------------
; video definitions
;---------------------------------------------------------------------------

; Display size in characters.  Note that simply changing these definitions
; won't have the desired effect.

rows		equ	4
columns		equ	20

; osc = 42,954,545 Hz = 12 * color burst
; tCYC = 23.2804 ns
; theoretical total width = 12 * 227.5 = 2730 cycles = 2 * 3 * 5 * 91 = 15 * 182
;
; The RTCC prescaler can only be set for powers of two, and we need the
; count to be a little under 256, so we use a prescaler of 16 and a divisor
; of 171, for an actual scan line width of 2736 cycles (63.7 us).

int_period			equ	171	; used by interrupt_done
h				equ	2736	; 63.7 us
hsync_pulse_width		equ	201	; 4.7 us
equalization_pulse_width	equ	98	; 2.3 us
serration_pulse_width	        equ	201	; 4.7 us
vsync_pulse_width		equ	(h/2)-serration_pulse_width
front_porch_width		equ	64	; 1.5 us
back_porch_width		equ	193	; 4.5 us

; safe area = 40 us = 1718 cycles
;
; 20 chars wide * (5+2) = 139 pixels wide, 12.4 cycles per pixel
; ("rounded" up to 13)
;
; for 4 3 aspect ratio, display should be 90 pixels tall, so make
; a pixel be 3 scan lines.

scan_lines_per_vpixel		equ	3
vpixels_per_char		equ	10
chars_per_row			equ	20

if ft_pal_video
total_active_lines		equ	287
else
total_active_lines		equ	242
endif

active_video_lines	equ	rows*vpixels_per_char*scan_lines_per_vpixel
top_border		equ	(total_active_lines-active_video_lines)/2
bottom_border		equ	total_active_lines-(top_border+active_video_lines)

;---------------------------------------------------------------------------
; composite video definitions
;---------------------------------------------------------------------------

vid_port		equ	rb	; D/A converter

; DAC 0 = ground (sync tip), 255 = 1.25V into 75 ohm load
; one DAC step = 1.25/255 V = 4.902 mV
; there are 140 IRE units to 1.0V, so an IRE unit is 7.143 mV = 1.457 DAC steps

vid_sync		equ	0	; -40 IRE
vid_blank		equ	58	; 58.29 = 0 IRE
vid_black		equ	69	; 69.21 = 7.5 IRE
vid_white		equ	204	; 204.00 = 100 IRE
vid_max_chroma		equ	249	; 249.17 = 131 IRE

burst_amplitude	equ	58	; 58.29 = 40 IREs

;---------------------------------------------------------------------------
; I/O port definitions
;---------------------------------------------------------------------------

rxd_bit			equ	0
pzt_bit			equ	1
txd_bit			equ	2	; not used
mode_button_bit	        equ	3	; not used

rxd			equ	ra.rxd_bit
pzt			equ	ra.pzt_bit
txd			equ	ra.txd_bit
mode_button		equ	ra.mode_button_bit

trisa			equ	$01	; RxD is our only input
inita			equ	$00

trisb			equ	$00	; all outputs
initb			equ	vid_sync

;---------------------------------------------------------------------------
; bell definitions
;---------------------------------------------------------------------------

; The bell tone is nominally around 500 Hz for 200 ms (100 cycles).
; This works out to a period of 32 scan lines.

bell_half_period	equ	16	; lines
bell_duration		equ	200	; half-periods

;---------------------------------------------------------------------------
; serial definitions
;---------------------------------------------------------------------------

; While serial line idle, sample every scan line.  Once start bit is
; detected, delay 6 scan lines, then sample every 13.  This results
; in a 1208 bps rate, 0.6% fast.

lines_per_serial_sample	equ	13

skip_on_ser_rx_mark	macro
noexpand
if ft_ser_noninv
expand
	        sb	rxd
noexpand
else
expand
	        snb	rxd
noexpand
endif
endm

skip_on_ser_rx_space	macro
noexpand
if ft_ser_noninv
expand
	        snb	rxd
noexpand
else
expand
	        sb	rxd
noexpand
endif
endm

;---------------------------------------------------------------------------
; memory utilization
;---------------------------------------------------------------------------

rambase		equ	08h		; start of RAM

rombase		equ	0000h		; beginning of program
romsize		equ	0800h
chargen		equ	romsize-384
intvec		equ	0000h		; interrupt vector

main_page	equ	0000h
int_page	equ	0200h

;---------------------------------------------------------------------------
; shared variables
;---------------------------------------------------------------------------

		org	rambase		; start of RAM

g_field_count	ds	1	; field down-counter

g_mtemp		ds	1	; global temp for main

; "DelM" uses "DelMCnt" in the interupt. Do NOT use DelM or DelMCnt in main!
DelMCnt		ds	1	; counter used for cycle delays
Five		ds	1
Fifteen		ds	1

;---------------------------------------------------------------------------
; variables for main
;---------------------------------------------------------------------------

		org	010h

main_vars

temp		ds	3

char		ds	1	; character being processed
escape_state	ds	1	; 0 = normal
				; 1 = ESC seen, waiting for 2nd char
				; 2 = ESC-Y seen, waiting for <col>
				; 3 = ESC-Y <col> seen, waiting for <row>
esc_Y_col	ds	1

; cursor
cursor_col	ds	1
cursor_row	ds	1
cursor_loc	ds	1

; for scrolling
src_addr	equ	temp
dest_addr	equ	temp+1
move_count	equ	temp+2

;---------------------------------------------------------------------------
; variables for interrupt
;---------------------------------------------------------------------------

		org	030h

int_vars

line_type	ds	1	; type of scan line we're working on
				;    2 * [0 .. line_types-1]
line_count	ds	1	; how many lines of this type to do

if ft_color
burst_phase	ds	1	; LSB used for burst phase
int_temp	ds	1	; general use in interrupt
endif

line_start	ds	1	; start buffer loc of currently displayed line
char_ptr	ds	1	; pointer to currently displayed character
chargen_ptr	ds	2	; pointer into character generator
inverse_flag	ds	1	; bit 7 indicates current char inverse
vpix_cnt	ds	1	; vertical pixel counter
scanline_cnt	ds	1	; vertical scan line counter (per pixel)
char_cnt	ds	1
pixels		ds	1	; pixels of current char

; bell
bell_half_cyc	ds	1	; bell half-cycle in lines
bell_line_cnt	ds	1	; bell half-cycle down-counter
bell_dur_cnt	ds	1	; bell duration

;---------------------------------------------------------------------------
; variables for serial receive
;---------------------------------------------------------------------------

if ft_serial_input

		org	050h

ser_vars

ser_rx_state		ds	1
ser_rx_byte		ds	1
ser_rx_samp_cnt  	ds	1
ser_rx_bit_cnt		ds	1

ser_rx_char		ds	1
ser_rx_flag		ds	1

endif

;---------------------------------------------------------------------------
; video buffer
;---------------------------------------------------------------------------

; NOTE  subtract offset of 20h (space) before storing characters into
; video buffer

video_buffer	equ	070h	; 80 characters, uses last five banks
				; *must* start on a bank boundary

; reserve RAM, skipping over banks as needed
res_bank_ram	macro	1	;res_bank_ram count
noexpand
local1 = \1
rept	local1
expand
	        ds	1
noexpand
if ($ & 010h)=0
expand
	        org	$+010h
noexpand
endif
endr
endm

		org	video_buffer
line_0		res_bank_ram	columns
line_1		res_bank_ram	columns
line_2		res_bank_ram	columns-1
line_2_end	res_bank_ram	1
line_3		res_bank_ram	columns-1
line_3_end	res_bank_ram	1

		org	rombase

		page	interrupt	; 0
		jmp	interrupt	; 1

escape_state_table
		mov	W, escape_state
		add	PC, W
		jmp	esc_not_seen
		jmp	esc_seen
		jmp	esc_Y_col_seen
		jmp	esc_Y_row_seen

control_char_table
		mov	W, char
		add	PC, W
		jmp	null			; 00 - NUL - null - don't do anything
		jmp	null			; 01 -
		jmp	null			; 02 -
		jmp	null			; 03 -
		jmp	null			; 04 -
		jmp	null			; 05 -
		jmp	null			; 06 -
		jmp	bell			; 07 - BEL - bell
		jmp	backspace		; 08 - BS - backspace
		jmp	null			; 09 -
		jmp	line_feed		; 0a - LF - line feed
		jmp	null			; 0b -
		jmp	form_feed		; 0c - FF - form feed - clear screen
		jmp	carriage_return	        ; 0d - CR - carriage return
		jmp	null			; 0e
		jmp	null			; 0f
		jmp	null			; 10
		jmp	null			; 11
		jmp	null			; 12
		jmp	null			; 13
		jmp	null			; 14
		jmp	null			; 15
		jmp	null			; 16
		jmp	null			; 17
		jmp	null			; 18
		jmp	null			; 19
		jmp	null			; 1a
		jmp	escape			; 1b - ESC - escape
		jmp	null			; 1c
		jmp	null			; 1d
		jmp	null			; 1e
		jmp	null			; 1f

esc_char_table
		add	PC, W
		jmp	bad_escape		; 40 - @
		jmp	cursor_up		; 41 - A - cursor up
		jmp	cursor_down		; 42 - B - cursor down
		jmp	cursor_left		; 43 - C - cursor left
		jmp	cursor_right		; 44 - D - cursor right
		jmp	bad_escape		; 45 - E
		jmp	bad_escape		; 46 - F
		jmp	bad_escape		; 47 - G
		jmp	home_cursor		; 48 - H - cursor home
		jmp	rev_line_feed		; 49 - I - reverse line feed (can scroll)
		jmp	clear_eop		; 4A - J - clear to end of screen
		jmp	clear_eol		; 4B - K - clear to end of line
		jmp	bad_escape		; 4C - L
		jmp	bad_escape		; 4D - M
		jmp	bad_escape		; 4E - N
		jmp	bad_escape		; 4F - O
		jmp	bad_escape		; 50 - P
		jmp	bad_escape		; 51 - Q
		jmp	bad_escape		; 52 - R
		jmp	bad_escape		; 53 - S
		jmp	bad_escape		; 54 - T
		jmp	bad_escape		; 55 - U
		jmp	bad_escape		; 56 - V
		jmp	bad_escape		; 57 - W
		jmp	bad_escape		; 58 - X
		jmp	esc_Y			; 59 - Y - cursor positioning
		jmp	bad_escape		; 5A - Z
		jmp	bad_escape		; 5B - [
		jmp	bad_escape		; 5C - 
		jmp	bad_escape		; 5D - ]
		jmp	bad_escape		; 5E - ^
		jmp	bad_escape		; 5F - _

show_cursor
		mov	W, cursor_loc
		mov	fsr, W
		setb	indf.7
		bank	main_vars
		ret

hide_cursor
		mov	W, cursor_loc
		mov	fsr, W
		clrb	indf.7
		bank	main_vars
		ret

; delay until either the number of fields specified in W have been
; displayed (zero flag set), or a serial character is received
; (zero flag clear)

delay_fields
		bank	ser_vars
		mov	g_field_count, W

df_loop
if ft_serial_input

		test	ser_rx_flag	; check serial receive flag
		sb	status.zf	; character received?
		jmp	df_return	; yes, return to caller

endif

		test	g_field_count	; has field count decremented to zero?
		sb	status.zf
		jmp	df_loop		; no, keep looping

df_return
		bank	main_vars
		ret


home_cursor
		clr	cursor_row

carriage_return
		clr	cursor_col

compute_cursor_loc
		mov	W, cursor_row	        ; cursor_loc = 20 * cursor_row
		mov	cursor_loc, W
		clrb	status.cf
		rl	cursor_loc
		rl	cursor_loc
		mov	W, <>cursor_row
		add	cursor_loc, W

		mov	W, cursor_col	        ; cursor_loc += cursor_col
		add	cursor_loc, W

		mov	W, cursor_loc           ; shift high nibble left one bit
		and	W, #0f0h
		add	cursor_loc, W

		mov	W, #video_buffer	; add in base address
		add	cursor_loc, W
null
		ret


; output a character from W to the display
output_char
		and	W, #07fh	        ; strip MSB (parity?) and save
		mov	char, W
		jmp	escape_state_table	; process character


esc_not_seen
		mov	W, char
		and	W, #060h	        ; is it a control character?
		snb	status.zf
		jmp	control_char_table	; yes, process and return

		mov	W, char		        ; is it a DEL
		xor	W, #asc_del
		snb	status.zf
		ret			        ; yes, do nothing

		mov	W, char
		; fall into printable_char

printable_char
		mov	g_mtemp, W	        ; save character

		mov	W, #-' '	        ; remove offset
		add	g_mtemp, W

		mov	W, cursor_loc           ;  store character
		mov	fsr, W
		mov	W, g_mtemp
		mov	indf, W
		bank	 main_vars
		; fall into cursor_advance

cursor_advance
		inc	cursor_col
		mov	W, cursor_col
		xor	W, #columns
		sb	status.zf
		jmp	compute_cursor_loc

crlf
	        clr     cursor_col
line_feed
		inc	cursor_row
		mov	W, cursor_row
		xor	W, #rows
		sb	status.zf
		jmp	compute_cursor_loc
		dec	cursor_row	; restore
		call	compute_cursor_loc

scroll_up
		mov	W, #line_1
		mov	src_addr, W
		mov	W, #line_0
		mov	dest_addr, W
		mov	W, #(rows-1)*columns
		mov	move_count, W
		call	block_move_up

		mov	W, #line_3	          ; clear freed space
		mov	temp+1, W
		mov	W, #columns
		mov	temp, W
		jmp	clear_chars


block_move_up
		mov	W, src_addr
		mov	fsr, W
		mov	W, indf
		mov	g_mtemp, W
		bank	main_vars
		inc	src_addr
		setb	src_addr.4

		mov	W, dest_addr
		mov	fsr, W
		mov	W, g_mtemp
		mov	indf, W
		bank	main_vars
		inc	dest_addr
		setb	dest_addr.4

		decsz	move_count
		jmp	block_move_up

		ret


backspace
		dec	cursor_col
		sb	cursor_col.7
		jmp	compute_cursor_loc
		mov	W, #columns-1
		mov	cursor_col, W

rev_line_feed
		dec	cursor_row
		sb	cursor_row.7
		jmp	compute_cursor_loc
		inc	cursor_row	; restore
		call	compute_cursor_loc

scroll_down
		mov	W, #line_2_end
		mov	src_addr, W
		mov	W, #line_3_end
		mov	dest_addr, W
		mov	W, #(rows-1)*columns
		mov	move_count, W
		call	block_move_down

		mov	W, #line_0 ; clear freed space
		mov	temp+1, W
		mov	W, #columns
		mov	temp, W
		jmp	clear_chars

block_move_down
		mov	W, src_addr
		mov	fsr, W
		mov	W, indf
		mov	g_mtemp, W
		bank	main_vars
		dec	src_addr
		snb	src_addr.4
		jmp	bmd_1
		mov	W, #010h
		sub	src_addr, W

bmd_1
		mov	W, dest_addr
		mov	fsr, W
		mov	W, g_mtemp
		mov	indf, W
		bank	main_vars
		dec	dest_addr
		snb	dest_addr.4
		jmp	bmd_2
		mov	W, #010h
		sub	dest_addr, W

bmd_2
		decsz	move_count
		jmp	block_move_down
		ret


clear_eol
		mov	W, #columns	; compute number of chars to clear
		mov	temp, W		; temp  = columns - cursor_col
		mov	W, cursor_col
		sub	temp, W

		mov	W, cursor_loc
		mov	temp+1, W

; clear temp chars starting at loc temp+1
clear_chars
		mov	W, #' '-020h
		mov	g_mtemp, W

; fill temp chars starting at loc temp+1 to value temp+2
fill_chars
		mov	W, temp+1
		mov	fsr, W
		mov	W, g_mtemp
		mov	indf, W
		bank	main_vars

		inc	temp+1
		setb	temp+1.4
		decsz	temp
		jmp	fill_chars
		ret


form_feed
		call	home_cursor

clear_eop
		call	clear_eol	; clear to end of current line
		mov	W, #rows-1	; compute additional rows to clear
		mov	temp, W		; temp  = (rows - 1) - cursor_row
		mov	W, cursor_row
		sub	temp, W
		snb	status.zf	; any rows to clear?
		ret			; no

		clrb	status.cf	; multiply temp by 20 to get char count
		rl	temp
		clrb	status.cf
		rl	temp
		mov	W, temp
		clrb	status.cf
		rl	temp
		clrb	status.cf
		rl	temp
		add	temp, W

		jmp	fill_chars


cursor_up
		dec	cursor_row
		mov	W, #rows-1
		snb	cursor_row.7
		mov	cursor_row, W
		jmp	compute_cursor_loc

cursor_down
		inc	cursor_row
		snb	cursor_row.2	; hard-coded for 4 rows
		clr	cursor_row
		jmp	compute_cursor_loc

cursor_left
		dec	cursor_col
		mov	W, #columns-1
		snb	cursor_col.7
		mov	cursor_col, W
		jmp	compute_cursor_loc

cursor_right
		inc	cursor_col
		mov	W, cursor_col
		xor	W, #columns
		snb	status.zf
		clr	cursor_row
		jmp	compute_cursor_loc


esc_Y
		mov	W, #2
		mov	escape_state, W
bad_escape
		ret

esc_Y_col_seen
		mov	W, #' '
		mov	W, char-w
		mov	esc_Y_col, W
		inc	escape_state
		ret

escape
		inc	escape_state
		ret

esc_Y_row_seen
		mov	W, #(256-' ')-rows	; range check the row (still has ' ' offset)
		add	W, char
		snb	status.cf
		jmp	bad_row

		mov	W, #' '		; move cursor to specified column
		mov	W, char-w
		mov	cursor_row, W
bad_row

		mov	W, #256-columns	; range check the column
		add	W, esc_Y_col
		snb	status.cf
		jmp	bad_col

		mov	W, esc_Y_col	; move cursor to specified column
		mov	cursor_col, W
bad_col

		clr	escape_state
		jmp	compute_cursor_loc


esc_seen
		clr	escape_state	; assume only two-char sequence
		mov	W, #$40
		mov	W, char-w
		mov	temp, W
		and	W, #060h	; check for range 40-5F
		sb	status.zf
		jmp	bad_escape

		mov	W, temp
		jmp	esc_char_table


bell
		bank	int_vars ; start a bell
		mov	W, #bell_half_period
		mov	bell_half_cyc, W
		mov	bell_line_cnt, W
		mov	W, #bell_duration
		mov	bell_dur_cnt, W
		bank	main_vars
		ret


reset_entry
		mode	0fh	; paranoia

		mov	W, #int_off
		mov	!OPTION, W

		bank	main_vars

		mov	W, #inita
		mov	Ra, W
		mov	W, #trisa
		mov	!ra,w

		mov	W, #initb
		mov	Rb, W
		mov	W, #trisb
		mov	!rb,w

		clr	escape_state
		call	form_feed

		bank	int_vars

		mov	W, #5	; set up for DelM macro
		mov	Five, W
		mov	W, #15
		mov	Fifteen, W

		clr	line_type

		mov	W, ++line_type		; get initial line count
		page	line_dispatch
		call	line_dispatch
		page	$
		mov	line_count, W

if ft_serial_input

		bank	ser_vars

		clr	ser_rx_state
		mov	W, #1
		mov	ser_rx_samp_cnt, W
		clr	ser_rx_flag

endif

		bank	main_vars

		mov	W, #int_on
		mov	!OPTION, W

if ft_splash
		page	splash
		call	splash
endif

                ;call   home_cursor

main_loop
		call	show_cursor
if ft_pal_video
                mov     W, #25
else
		mov	W, #30
endif
		call	delay_fields

if ft_serial_input
		sb	status.zf
		jmp	got_char
endif

		call	hide_cursor
if ft_pal_video
                mov     W, #25
else
		mov	W, #30
endif
		call	delay_fields

if ft_serial_input
		sb	status.zf
		jmp	got_char
endif

		jmp	main_loop


if ft_serial_input
got_char
		call	hide_cursor	; hide cursor during character processing

		bank	ser_vars	; get character and clear rx flag
		mov	W, ser_rx_char
		clr	ser_rx_flag
		bank	main_vars

		call	output_char
		jmp	main_loop
endif


;---------------------------------------------------------------------------
; interrupt handler
;---------------------------------------------------------------------------

		org	0200h

; 30-DEC-2000   Eric Smith
; changed for GPASM assembler

;6-JAN-2000 Richard Ottosen

;This routine is for the SX parts in Turbo mode only. It does not matter if the
; Carry fuse is set or clear.
;
;Macro to delay for M number of cycles from 0 through 65535.
;  The macro includes paging for long calls.
;
;Uses the routine "DelW" to do the short delays and uses the variable "DelMCnt"
;  as well for long delays.
;The constants 5 and 15 must be loaded into variables "Five" and "Fifteen"
; before DelM is used.
;
;
DelM	MACRO	1	;DelM _MM
noexpand
local2 = \1
IF (local2 & $FF)=0		;No delay at all
ENDIF
IF (local2 & $FF)=1
		nop		;Delay 1 cycle inline
ENDIF
IF (local2 & $FF)=2
		nop		;Delay 2 cycles inline
		nop
ENDIF
IF (local2 & $FF)=3
		jmp	$+1	;Delay 3 cycles inline
ENDIF
IF (local2 & $FF)=4
		jmp	$+1	;Delay 4 cycles inline
		nop
ENDIF
IF (local2 & $FF)=5
		jmp	$+1	;Delay 5 cycles inline
		nop
		nop
ENDIF
IF (local2 & $FF)=6
		jmp	$+1	;Delay 6 cycles inline
		jmp	$+1
ENDIF
IF (local2 & $FF)=7
		PAGE	Delay6
		call	Delay6	;Delay 7 cycles
ENDIF
IF (local2 & $FF)=8
		PAGE	Delay7
		call	Delay7	;Delay 8 cycles
ENDIF
IF (local2 & $FF)=9
		PAGE	Delay8
		call	Delay8	;Delay 9 cycles
ENDIF
IF (local2 & $FF)=10
		PAGE	Delay9
		call	Delay9	;Delay 10 cycles
ENDIF
IF (local2 & $FF)=11
		PAGE	Delay10
		call	Delay10		;Delay 11 cycles
ENDIF
IF (local2 & $FF)=12
		PAGE	Delay11
		call	Delay11		;Delay 12 cycles
ENDIF
IF (local2 & $FF)=13
		PAGE	Delay12
		call	Delay12		;Delay 13 cycles
ENDIF
IF (local2 & $FF)=14
		PAGE	Delay13
		call	Delay13		;Delay 14 cycles
ENDIF
IF (local2 & $FF)=15
		PAGE	Delay14
		call	Delay14		;Delay 15 cycles
ENDIF
IF (local2 & $FF)=16
		PAGE	Delay15
		call	Delay15		;Delay 16 cycles
ENDIF
IF (local2 & $FF)>16
		mov	W, #((local2-1) & $FF)
		PAGE	DelW
		call	DelW		;Delay for 17 thru 255 cycles
ENDIF
IF (local2 >> 8)<>0
		mov	W, #(local2 >> 8)	;Delay more for greater than 255 cycles
		mov	DelMCnt, W
;_DelMLoop
		mov	W, #251
		PAGE	DelW
		call	DelW
		decsz	DelMCnt
		jmp	$-4			;jmp _DelMLoop
ENDIF
ENDM

; original gpasm source macro by Eric Smith  7/8/96 Hacked by Richard Ottosen 8/8/99
; converted to sx-key mnenomics by Peter Verkaik

;-----------------------------------------------------------------------------
;This version of DelW is for the Scenix parts in Turbo mode. It does not matter
;if the Carry fuse is set or clear.
; DelW delays W cycles, including call, return, and one cycle for the
; mov W, #instruction to set up the count in W
; range is 16..255
;
; For example, the sequence
; mov W, #17
; call DelW
; will take 17 cycles to execute
;-----------------------------------------------------------------------------

; W value on entry		 	  16   17   18   19   20     21     22     23
; Caller's instructions		         ---  ---  ---  ---  ---  -----  -----  -----
;		mov	W, #n		   0    0    0    0    0    0      0      0
;		call	DelW		   1    1    1    1    1    1      1      1

DelW		setb	status.cf	;  4    4    4    4    4    4      4      4
		mov	W, Fifteen-w	;  5    5    5    5    5    5      5      5
_DelWLp		add	W, Five		;  6    6    6    6    6    6 11   7 11   7 11
		sb	status.cf	;  7    7    7    7    7    7 12     12     12
		jmp	_DelWLp		;                           8      8      8
		clrb	status.cf	;  9    9    9    9    9      14     14     14
		add	PC, W		; 10   10   10   10   10      15     15     15
Delay10		nop			;                     13
Delay9		nop			;                13   14
Delay8		nop			;           13   14   15                 18
Delay7		nop			;      13   14   15   16             18     19
Delay6		retp			; 13   14   15   16   17      18     19     20
					; 16   17   18   19   20      21     22     23

Delay15		nop
Delay14		nop
Delay13		nop
Delay12		nop
Delay11		jmp	Delay8


scanln	macro	2	;scanln count,function
expand
		jmp    \2     ;jmp function
		retw   \1     ;retw count
noexpand
endm


; table of line type function pointers and counts
; when called for function, takes cycles 58-63

line_dispatch
		add	PC, W ; 58

if ft_pal_video

		; PAL lines
		scanln	2,equalization_line ; 624-625
		scanln	2,vsync_line ; 1-2
		scanln	1,vsync_eq_line ; 3
		scanln	2,equalization_line ; 4-5
		scanln	17,vblank_line ; 6-22
		scanln	1,vblank_black_line ; 23
		scanln	top_border,black_video_line ; 24-106
		scanln	active_video_lines,active_video_line ; 107-226
		scanln	bottom_border-1,black_video_line ; 227-309

	if ft_interlace
		scanln	1,black_video_line ; 310
		scanln	2,equalization_line ; 311-312
		scanln	1,eq_vsync_line ; 313
		scanln	2,vsync_line ; 314-315
		scanln	2,equalization_line ; 316-317
		scanln	1,eq_vblank_line ; 318
		scanln	17,vblank_line ; 319-335
		scanln	top_border,black_video_line ; 336-418
		scanln	active_video_lines,active_video_line ; 419-538
		scanln	bottom_border,black_video_line ; 539-622
	endif

		scanln	1,black_eq_line ; 310 or 623

else

		; NTSC lines
		scanln	3,equalization_line ; 1-3
		scanln	3,vsync_line ; 4-6
		scanln	3,equalization_line ; 7-9
		scanln	11,vblank_line ; 10-20
		scanln	top_border,black_video_line ; 21-81
		scanln	active_video_lines,active_video_line ; 82-201
		scanln	bottom_border,black_video_line ; 202-262

	if ft_interlace
		scanln	1,black_eq_line ; 263
		scanln	2,equalization_line ; 264-265
		scanln	1,eq_vsync_line ; 266
		scanln	2,vsync_line ; 267-268
		scanln	1,vsync_eq_line ; 269
		scanln	2,equalization_line ; 270-271
		scanln	1,eq_vblank_line ; 272
		scanln	10,vblank_line ; 273-282
		scanln	1,vblank_black_line ; 283
		scanln	top_border,black_video_line ; 284-344
		scanln	active_video_lines,active_video_line ; 345-464
		scanln	bottom_border,black_video_line ; 465-525
	endif

endif


line_types	equ	(($-line_dispatch)-1)/2


if ft_serial_input
; serial input state machine dispatch
serial_state_table
		mov	W, ser_rx_state	; 12
		add	PC, W			; 13-15
		jmp	ser_idle		; 16-18
		jmp	ser_data_bit		; 16-18
		jmp	ser_stop_bit		; 16-18
endif


bell_48
		clrb	pzt			; 48
		delm	1			; 49
bell_50
		delm	1			; 50
		jmp	bell_done		; 51-53


interrupt
		mov	W, #vid_blank		; 4 start front porch
		mov	vid_port, W		; 5

if ft_serial_input

		bank	ser_vars		; 6
		decsz	ser_rx_samp_cnt	; 7
		jmp	skip_serial		; 8-10

		call	serial_state_table	; 9-11
		jmp	serial_done		; 39-41

skip_serial
		delm	31			; 11-41
serial_done

else

		delm	36			; 6-41

endif

		bank	int_vars		; 42

		test	bell_dur_cnt		; 43 - bell active?
		snb	status.zf		; 44
		jmp	bell_48			; 45-47 - no

		decsz	bell_line_cnt		; 46 - time to toggle PZT?
		jmp	bell_50			; 47-49 - no

		mov	W, #1<<pzt_bit		; 48 - toggle PZT
		xor	Ra, W			; 49

		dec	bell_dur_cnt		; 50 - decrement duration

		mov	W, bell_half_cyc	; 51 - reinit line count
		mov	bell_line_cnt, W	; 52

		delm	1			; 53
bell_done

		mov	W, line_type		; 54
		call	line_dispatch		; 55-57

		decsz	line_count		; any more lines of the current type?
		jmp	interrupt_done		; no, done

		inc	line_type		; advance to next line type
		inc	line_type
		mov	W, line_type		; end of field?
		xor	W, #line_types*2
		sb	status.zf
		jmp	get_line_count		; no

		clr	line_type		; yes, start new field

		test	g_field_count		; decrement field counter
		sb	status.zf
		dec	g_field_count

get_line_count
		mov	W, ++line_type		; new line type, how many lines?
		call	line_dispatch
		mov	line_count, W

interrupt_done
		mov	W, #256-int_period	; all done with this scan line
		retiw


; at some point within the frame before the first active video line,
; call this subroutine to initialize the pointers
display_frame_setup
		mov	W, #video_buffer
		mov	line_start, W

		clr	vpix_cnt

		mov	W, #scan_lines_per_vpixel
		mov	scanline_cnt, W

		ret


if ft_color

burst_l		equ	vid_blank-(burst_amplitude/2)
burst_h		equ	vid_blank+(burst_amplitude/2)
burst_x		equ	burst_l^burst_h

; burst starts at 228 cycles from horizontal reference point,
; which is 292 cycles from our start of back porch.

color_burst
		delm	14		; 270-283

; $$$ actually, don't toggle burst phase, because our current
; line timing is an integral multiple of the color carrier
		mov	W, #0		; 284 - toggle burst phase
		xor	burst_phase, W	; 285

		mov	W, #18		; 286 - 18 half-cycles of burst
		mov	int_temp, W	; 287

		mov	W, #burst_h	; 288 - assume leading edge high
		snb	burst_phase.0	; 289
		mov	W, #burst_l	; 290

burst_loop
		xor	W, #burst_x	; 291 399
		mov	vid_port, W	; 292 400
		decsz	int_temp	; 293 401
		jmp	burst_loop	; 294-296 402

		delm	2		; 403
		mov	W, #vid_blank	; 405
		mov	vid_port, W	; 406

		delm	48		; 407
		ret			; 455-457

else

color_burst
		delm	185		; 270-454
		ret			; 455-457

endif


equalization_line
		mov	W, #vid_sync	; 64 - start equalizing pulse
		mov	vid_port, W
		delm	equalization_pulse_width-2

		mov	W, #vid_blank	; end equalizing pulse
		mov	vid_port, W
		delm	((h/2)-equalization_pulse_width)-2

eq_second_half
		mov	W, #vid_sync	; start equalizing pulse
		mov	vid_port, W
		delm	equalization_pulse_width-2

		mov	W, #vid_blank	; end equalizing pulse
		mov	vid_port, W
		ret


vsync_line
		mov	W, #vid_sync	; 64 - start vsync pulse
		mov	vid_port, W
		delm	vsync_pulse_width-2

		mov	W, #vid_blank	; end vsync pulse - start serration
		mov	vid_port, W
		delm	serration_pulse_width-2

vsync_second_half
		mov	W, #vid_sync	; start vsync pulse
		mov	vid_port, W
		delm	vsync_pulse_width-2

		mov	W, #vid_blank	; end vsync pulse - start serration
		mov	vid_port, W
		ret


vblank_line
		mov	W, #vid_sync	; 64 - start hsync pulse
		mov	vid_port, W	; 65
		delm	hsync_pulse_width-2	; 66-264

		mov	W, #vid_blank	; 265 - end hsync pulse
		mov	vid_port, W	; 266
		call	color_burst	; 267-269
		ret


black_video_line
		mov	W, #vid_sync	; 64 - start hsync pulse
		mov	vid_port, W	; 65
		delm	hsync_pulse_width-2	; 66-264

		mov	W, #vid_blank	; 265 - end hsync pulse, start back porch
		mov	vid_port, W	; 266

		call	color_burst	; 267-269

		mov	W, #vid_black	; 458 - end back porch, start active video
		mov	vid_port, W	; 459

		jmp	display_frame_setup	; $$$ not the best place for this?
						; ret


if ft_interlace|ft_pal_video
; NTSC line 263, PAL line 623 (interlaced), PAL line 310 (non-interlaced)
black_eq_line
		mov	W, #vid_sync	; 64 - start hsync pulse
		mov	vid_port, W	; 65
		delm	hsync_pulse_width-2	; 66-264

		mov	W, #vid_blank	; 265 - end hsync pulse, start back porch
		mov	vid_port, W	; 266

		call	color_burst	; 267-269

		mov	W, #vid_black	; 458 - end back porch, start active video
		mov	vid_port, W	; 459
		delm	((h/2)-(hsync_pulse_width+back_porch_width))-5
		jmp	eq_second_half
endif


if ft_interlace
; NTSC line 266, PAL line 313
eq_vsync_line
		mov	W, #vid_sync	; 64 - start equalizing pulse
		mov	vid_port, W
		delm	equalization_pulse_width-2

		mov	W, #vid_blank	; end equalizing pulse
		mov	vid_port, W
		delm	((h/2)-equalization_pulse_width)-5
		jmp	vsync_second_half
endif


if ft_interlace|ft_pal_video
; NTSC line 269, PAL line 3
vsync_eq_line
		mov	W, #vid_sync	; 64 - start vsync pulse
		mov	vid_port, W
		delm	vsync_pulse_width-2

		mov	W, #vid_blank	; end vsync pulse - start serration
		mov	vid_port, W
		delm	serration_pulse_width-5
		jmp	eq_second_half
endif


if ft_interlace
; NTSC line 272 - like an equalization, but a full line with only one pulse
; PAL line 318
eq_vblank_line
		mov	W, #vid_sync	; 64 - start equalizing pulse
		mov	vid_port, W
		delm	equalization_pulse_width-2

		mov	W, #vid_blank	; end equalizing pulse
		mov	vid_port, W
		ret
endif


if ft_interlace|ft_pal_video
; NTSC line 283, PAL line 23
vblank_black_line
		mov	W, #vid_sync	; 64 - start hsync pulse
		mov	vid_port, W	; 65
		delm	hsync_pulse_width-2	; 66-264

		mov	W, #vid_blank	; 265 - end hsync pulse
		mov	vid_port, W	; 266

		call	color_burst	; 267-269

		delm	((h/2)+front_porch_width)-458	; 458-1431

		mov	W, #vid_black	; 1432 - start active video
		mov	vid_port, W
		ret
endif


active_video_line
		mov	W, #vid_sync	; 64 - start hsync pulse
		mov	vid_port, W	; 65
		delm	hsync_pulse_width-2	; 66-264

		mov	W, #vid_blank	; 265 - end hsync pulse, start back porch
		mov	vid_port, W	; 266

		call	color_burst	; 267-269

		mov	W, #vid_black	; 458 - end back porch, start active video
		mov	vid_port, W	; 459

		snb	vpix_cnt.3	; vpixel >= 8?
		jmp	active_video_line_done

		delm	100

		mov	W, line_start
		mov	char_ptr, W

		mov	W, #chars_per_row+1
		mov	char_cnt, W

; leading dummy character is always blank, allows us to fill
; the pixel pipeline
		clr	pixels

character
; pixel 0

		mov	W, #vid_black		; 0
		snb	pixels.0		; 1
		mov	W, #vid_white		; 2
		mov	vid_port, W		; 3

		mov	W, char_ptr		; 4 - get next character
		mov	fsr, W			; 5
		mov	W, indf			; 6
		bank	int_vars		; 7

		mov	inverse_flag,	W	; 8
		and	W, #07fh		; 9
		mov	chargen_ptr, W		; 10

		mov	W, --char_cnt		; 11 - increment buffer pointer
		sb	status.zf		; 12 -   unless we're at end of line
		inc	char_ptr		; 13 -   (due to pipeline, we pass through
		setb	char_ptr.4		; 14 -   here columns+1 times)

; pixel 1

		mov	W, #vid_black		; 0
		snb	pixels.1		; 1
		mov	W, #vid_white		; 2
		mov	vid_port, W		; 3

		mov	W, #(chargen/4)&0ffh	; 4 - add low part of chargen base
		add	chargen_ptr, W		; 5

		mov	W, #(chargen/4)>>8	; 6 - add high part of chargen base
		mov	chargen_ptr+1, W	; 7
		snb	status.cf		; 8
		inc	chargen_ptr+1		; 9

		clrb	status.cf		; 10 - rotate high bit of vpix_cnt into
		snb	vpix_cnt.2		; 11 - table address
		setb	status.cf		; 12
		rl	chargen_ptr		; 13
		rl	chargen_ptr+1		; 14

; pixel 2

		mov	W, #vid_black		; 0
		snb	pixels.2		; 1
		mov	W, #vid_white		; 2
		mov	vid_port, W		; 3

		clrb	status.cf		; 4 - rotate next bit of vpix_cnt into
		snb	vpix_cnt.1		; 5 - table address
		setb	status.cf		; 6
		rl	chargen_ptr		; 7
		rl	chargen_ptr+1		; 8

		delm	6			; 9-14

; pixel 3

		mov	W, #vid_black		; 0
		snb	pixels.3		; 1
		mov	W, #vid_white		; 2
		mov	vid_port, W		; 3

		DelM	11			; 4-14

; pixel 4

		mov	W, #vid_black		; 0
		snb	pixels.4		; 1
		mov	W, #vid_white		; 2
		mov	vid_port, W		; 3

		mov	W, chargen_ptr+1	; 4
		mov     m,w			; 5
		mov	W, chargen_ptr		; 6
		iread				; 7-10
		mov	pixels, W		; 11
		mov     w,m			; 12
		mode	0fh			; 13
		mov	chargen_ptr, W		; 14 - now use chargen_ptr as a temp

; intercharacter space

		snb	vpix_cnt.0		; 0 - get left four pixels into bits 0..3
		swap	pixels			; 1
		mov	W, #vid_black		; 2
		mov	vid_port, W		; 3
		clrb	pixels.4		; 4

		snb	vpix_cnt.0		; 5 - get rightmost pixel into bit 4
		rr	chargen_ptr		; 6
		snb	chargen_ptr.0		; 7
		setb	pixels.4		; 8

		mov	W, #01fh		; 9 - invert if needed
		snb	inverse_flag.7		; 10
		xor	pixels, W		; 11

; $$$ add more inter-character spacing here?

		decsz	char_cnt		; 12
		jmp	character		; 13-15

active_video_line_done

		decsz	scanline_cnt		; more scan lines for this pixel row?
		ret
		mov	W, #scan_lines_per_vpixel
		mov	scanline_cnt, W

		inc	vpix_cnt		; more pixels for this character row?
		mov	W, vpix_cnt
		xor	W, #vpixels_per_char
		sb	status.zf
		ret

		clr	vpix_cnt
		mov	W, char_ptr		; advance buffer pointer to next character row
		mov	line_start, W

		ret


;---------------------------------------------------------------------------
; serial receive routine
;---------------------------------------------------------------------------

if ft_serial_input

ser_idle
		mov	W, #1 			; 19 - sample every line
		mov	ser_rx_samp_cnt, W	; 20

		skip_on_ser_rx_mark		; 21 - start bit detected?
		jmp	ser_ret_25		; 22-24 - no, return

		mov	W, #lines_per_serial_sample * 3 / 2		; 23
		mov	ser_rx_samp_cnt, W 	; 24 - skip start bit and sample first data bit
		; in middle of bit time

		mov	W, #8			; 25 - set up to receive 8 chars
		mov	ser_rx_bit_cnt, W	; 26

		clr	ser_rx_byte		; 27 - not needed for 8-bit chars

		inc	ser_rx_state		; 28 - advance to next state
		jmp	ser_ret_32		; 29-31


ser_data_bit
		clrb	status.cf		; 19 - read a bit
		skip_on_ser_rx_mark		; 20
		setb	status.cf		; 21
		rr	ser_rx_byte		; 22 - rotate into byte

		mov	W, #lines_per_serial_sample	; 23 - set up for next sample
		mov	ser_rx_samp_cnt, W		; 24

		decsz	ser_rx_bit_cnt		; 25 - all data bits read?
		jmp	ser_ret_29		; 26-28 - no

		mov	W, ser_rx_byte		; 27 - move char to buffer
		mov	ser_rx_char, W		; 28
		inc	ser_rx_flag		; 29 - signal main

		mov	W, #(lines_per_serial_sample * 11)/8	; 30 - set up for stop bit
		mov	ser_rx_samp_cnt, W				; 31

		inc	ser_rx_state		; 32 - advance to next state
		jmp	ser_ret_36		; 33-35


ser_stop_bit
		mov	W, #1			; 19 - sample every line
		mov	ser_rx_samp_cnt, W	; 20

		skip_on_ser_rx_mark		; 21 - line idle?
		clr	ser_rx_state		; 22 - yes, back to idle

ser_ret_23	delm	2			; 23-24
ser_ret_25	delm	4			; 25-28
ser_ret_29	delm	3			; 29-31
ser_ret_32	delm	4			; 32-35
ser_ret_36	ret				; 36-38

endif


;---------------------------------------------------------------------------
; splash screen
;---------------------------------------------------------------------------

if ft_splash

		org	400h

splash_table
		add	PC, W
		dw	asc_bel
		; 01234567890123456789
		dw	'SERVID 0.2 Copyright'
		dw	'2001 Eric Smith and', asc_cr, asc_lf
		dw	'Richard Ottosen', asc_cr, asc_lf
		dw	'(SXLIST challenge) '
		dw	0


splash
		clr	temp+2
splash_loop
		mov	W, temp+2
		call	splash_table
		xor	W, #0
		snb	status.zf
		retp
		page	output_char
		call	output_char	; $$$ change to end with retp?
		page	$
		inc	temp+2
		jmp	splash_loop

endif

;---------------------------------------------------------------------------
; character generator macros
;---------------------------------------------------------------------------

		org	chargen

cg_row1		macro	1	;cg_row1  pixels
noexpand
char1 = \1
r1_bits = 0
rept 5
r1_bits = (r1_bits*2)+(char1//10)
char1 = char1/10
endr
endm

cg_row2		macro	1	;cg_row2  pixels
noexpand
char2 = \1
r2_bits = 0
rept 5
r2_bits = (r2_bits*2)+(char2//10)
char2 = char2/10
endr
expand
dw ((r1_bits&010h)<<4)+(r1_bits&0fh)+((r2_bits&010h)<<5)+((r2_bits&0fh)<<4)
noexpand
endm

; SERVID character set
; $Id  charset.inc,v 1.4 2001/01/04 04 58 40 eric Exp $
;
; Copyright 2001 Richard Ottosen and Loren Blaney
;
; This program is free software; you can redistribute it and/or modify
; it under the terms of the GNU General Public License version 2 as published
; by the Free Software Foundation.  Note that permission is not granted
; to redistribute this program under the terms of any other version of the
; General Public License.
;
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with this program; if not, write to the Free Software
; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
;
; Licenses for non-GPL use may be negotiated with the authors.
;
; originally from Bion as a vertical font
; used by Richard Ottosen's Whirlygig
; rotated to horizontal form by Loren Blaney
; munged for SERVID by Richard Ottosen

		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000	;20h

		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000 ;21h

		cg_row1 01010
		cg_row2 01010
		cg_row1 01010
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;22h

		cg_row1 01010
		cg_row2 01010
		cg_row1 11111
		cg_row2 01010
		cg_row1 11111
		cg_row2 01010
		cg_row1 01010
		cg_row2 00000 ;23h

		cg_row1 00100
		cg_row2 01111
		cg_row1 10100
		cg_row2 01110
		cg_row1 00101
		cg_row2 11110
		cg_row1 00100
		cg_row2 00000 ;24h

		cg_row1 11000
		cg_row2 11001
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 10011
		cg_row1 00011
		cg_row2 00000 ;25h

		cg_row1 01000
		cg_row2 10100
		cg_row1 10100
		cg_row2 01000
		cg_row1 10101
		cg_row2 10010
		cg_row1 01101
		cg_row2 00000 ;26h

		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;27h

		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 01000
		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00000 ;28h

		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00010
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 00000 ;29h

		cg_row1 00100
		cg_row2 10101
		cg_row1 01110
		cg_row2 00100
		cg_row1 01110
		cg_row2 10101
		cg_row1 00100
		cg_row2 00000 ;2Ah

		cg_row1 00000
		cg_row2 00100
		cg_row1 00100
		cg_row2 11111
		cg_row1 00100
		cg_row2 00100
		cg_row1 00000
		cg_row2 00000 ;2Bh

		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00100
		cg_row2 00100
		cg_row1 01000
		cg_row2 00000 ;2Ch

		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 11111
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;2Dh

		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000 ;2Eh

		cg_row1 00000
		cg_row2 00001
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 10000
		cg_row1 00000
		cg_row2 00000 ;2Fh

		cg_row1 01110
		cg_row2 10001
		cg_row1 10011
		cg_row2 10101
		cg_row1 11001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;30h

		cg_row1 00100
		cg_row2 01100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 01110
		cg_row2 00000 ;31h

		cg_row1 01110
		cg_row2 10001
		cg_row1 00001
		cg_row2 00110
		cg_row1 01000
		cg_row2 10000
		cg_row1 11111
		cg_row2 00000 ;32h

		cg_row1 11111
		cg_row2 00001
		cg_row1 00010
		cg_row2 00110
		cg_row1 00001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;33h

		cg_row1 00010
		cg_row2 00110
		cg_row1 01010
		cg_row2 10010
		cg_row1 11111
		cg_row2 00010
		cg_row1 00010
		cg_row2 00000 ;34h

		cg_row1 11111
		cg_row2 10000
		cg_row1 11110
		cg_row2 00001
		cg_row1 00001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;35h

		cg_row1 00111
		cg_row2 01000
		cg_row1 10000
		cg_row2 11110
		cg_row1 10001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;36h

		cg_row1 11111
		cg_row2 00001
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 01000
		cg_row1 01000
		cg_row2 00000 ;37h

		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 01110
		cg_row1 10001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;38h

		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 01111
		cg_row1 00001
		cg_row2 00010
		cg_row1 11100
		cg_row2 00000 ;39h

		cg_row1 00000
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;3Ah

		cg_row1 00000
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000
		cg_row1 00100
		cg_row2 00100
		cg_row1 01000
		cg_row2 00000 ;3Bh

		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 10000
		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00000 ;3Ch

		cg_row1 00000
		cg_row2 00000
		cg_row1 11111
		cg_row2 00000
		cg_row1 11111
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;3Dh

		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00001
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 00000 ;3Eh

		cg_row1 01110
		cg_row2 10001
		cg_row1 00010
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000
		cg_row1 00100
		cg_row2 00000 ;3Fh

		cg_row1 01110
		cg_row2 10001
		cg_row1 10101
		cg_row2 10111
		cg_row1 10110
		cg_row2 10000
		cg_row1 01111
		cg_row2 00000 ;40h

		cg_row1 00100
		cg_row2 01010
		cg_row1 10001
		cg_row2 10001
		cg_row1 11111
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;41h

		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 11110
		cg_row1 10001
		cg_row2 10001
		cg_row1 11110
		cg_row2 00000 ;42h

		cg_row1 01110
		cg_row2 10001
		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;43h

		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 11110
		cg_row2 00000 ;44h

		cg_row1 11111
		cg_row2 10000
		cg_row1 10000
		cg_row2 11110
		cg_row1 10000
		cg_row2 10000
		cg_row1 11111
		cg_row2 00000 ;45h

		cg_row1 11111
		cg_row2 10000
		cg_row1 10000
		cg_row2 11110
		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 00000 ;46h

		cg_row1 01111
		cg_row2 10000
		cg_row1 10000
		cg_row2 10000
		cg_row1 10011
		cg_row2 10001
		cg_row1 01111
		cg_row2 00000 ;47h

		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 11111
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;48h

		cg_row1 01110
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 01110
		cg_row2 00000 ;49h

		cg_row1 00001
		cg_row2 00001
		cg_row1 00001
		cg_row2 00001
		cg_row1 00001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;4Ah

		cg_row1 10001
		cg_row2 10010
		cg_row1 10100
		cg_row2 11000
		cg_row1 10100
		cg_row2 10010
		cg_row1 10001
		cg_row2 00000 ;4Bh

		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 10000
		cg_row1 11111
		cg_row2 00000 ;4Ch

		cg_row1 10001
		cg_row2 11011
		cg_row1 10101
		cg_row2 10101
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;4Dh

		cg_row1 10001
		cg_row2 10001
		cg_row1 11001
		cg_row2 10101
		cg_row1 10011
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;4Eh

		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;4Fh

		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 11110
		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 00000 ;50h

		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10101
		cg_row2 10010
		cg_row1 01101
		cg_row2 00000 ;51h

		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 11110
		cg_row1 10100
		cg_row2 10010
		cg_row1 10001
		cg_row2 00000 ;52h

		cg_row1 01110
		cg_row2 10001
		cg_row1 10000
		cg_row2 01110
		cg_row1 00001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;53h

		cg_row1 11111
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000 ;54h

		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;55h

		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 01010
		cg_row1 00100
		cg_row2 00000 ;56h

		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10101
		cg_row1 10101
		cg_row2 11011
		cg_row1 10001
		cg_row2 00000 ;57h

		cg_row1 10001
		cg_row2 10001
		cg_row1 01010
		cg_row2 00100
		cg_row1 01010
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;58h

		cg_row1 10001
		cg_row2 10001
		cg_row1 01010
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000 ;59h

		cg_row1 11111
		cg_row2 00001
		cg_row1 00010
		cg_row2 00100
		cg_row1 01000
		cg_row2 10000
		cg_row1 11111
		cg_row2 00000 ;5Ah

		cg_row1 11111
		cg_row2 11000
		cg_row1 11000
		cg_row2 11000
		cg_row1 11000
		cg_row2 11000
		cg_row1 11111
		cg_row2 00000 ;5Bh

		cg_row1 00000
		cg_row2 10000
		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00001
		cg_row1 00000
		cg_row2 00000 ;5Ch

		cg_row1 11111
		cg_row2 00011
		cg_row1 00011
		cg_row2 00011
		cg_row1 00011
		cg_row2 00011
		cg_row1 11111
		cg_row2 00000 ;5Dh

		cg_row1 00000
		cg_row2 00000
		cg_row1 00100
		cg_row2 01010
		cg_row1 10001
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;5Eh

		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 11111
		cg_row2 00000 ;5Fh

		cg_row1 01000
		cg_row2 00100
		cg_row1 00010
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;60h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01110
		cg_row2 00001
		cg_row1 01111
		cg_row2 10001
		cg_row1 01111
		cg_row2 00000 ;61h

		cg_row1 10000
		cg_row2 10000
		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 11110
		cg_row2 00000 ;62h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01111
		cg_row2 10000
		cg_row1 10000
		cg_row2 10000
		cg_row1 01111
		cg_row2 00000 ;63h

		cg_row1 00001
		cg_row2 00001
		cg_row1 01111
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 01111
		cg_row2 00000 ;64h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01110
		cg_row2 10001
		cg_row1 11111
		cg_row2 10000
		cg_row1 01111
		cg_row2 00000 ;65h

		cg_row1 00110
		cg_row2 01001
		cg_row1 01000
		cg_row2 11110
		cg_row1 01000
		cg_row2 01000
		cg_row1 01000
		cg_row2 00000 ;66h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 01111
		cg_row1 00001
		cg_row2 01110 ;67h

		cg_row1 10000
		cg_row2 10000
		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;68h

		cg_row1 00100
		cg_row2 00000
		cg_row1 01100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 01110
		cg_row2 00000 ;69h

		cg_row1 00010
		cg_row2 00000
		cg_row1 00010
		cg_row2 00010
		cg_row1 00010
		cg_row2 00010
		cg_row1 10010
		cg_row2 01100 ;6Ah

		cg_row1 10000
		cg_row2 10000
		cg_row1 10010
		cg_row2 10100
		cg_row1 11000
		cg_row2 10100
		cg_row1 10010
		cg_row2 00000 ;6Bh

		cg_row1 01100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 01110
		cg_row2 00000 ;6Ch

		cg_row1 00000
		cg_row2 00000
		cg_row1 11010
		cg_row2 10101
		cg_row1 10101
		cg_row2 10101
		cg_row1 10101
		cg_row2 00000 ;6Dh

		cg_row1 00000
		cg_row2 00000
		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 00000 ;6Eh

		cg_row1 00000
		cg_row2 00000
		cg_row1 01110
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 01110
		cg_row2 00000 ;6Fh

		cg_row1 00000
		cg_row2 00000
		cg_row1 11110
		cg_row2 10001
		cg_row1 10001
		cg_row2 11110
		cg_row1 10000
		cg_row2 10000 ;70h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01111
		cg_row2 10001
		cg_row1 10001
		cg_row2 01111
		cg_row1 00001
		cg_row2 00001 ;71h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10110
		cg_row2 11001
		cg_row1 10000
		cg_row2 10000
		cg_row1 10000
		cg_row2 00000 ;72h

		cg_row1 00000
		cg_row2 00000
		cg_row1 01111
		cg_row2 10000
		cg_row1 01110
		cg_row2 00001
		cg_row1 11110
		cg_row2 00000 ;73h

		cg_row1 00100
		cg_row2 00100
		cg_row1 11111
		cg_row2 00100
		cg_row1 00100
		cg_row2 00100
		cg_row1 00011
		cg_row2 00000 ;74h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 10001
		cg_row1 01111
		cg_row2 00000 ;75h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10001
		cg_row2 10001
		cg_row1 10001
		cg_row2 01010
		cg_row1 00100
		cg_row2 00000 ;76h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10001
		cg_row2 10101
		cg_row1 10101
		cg_row2 10101
		cg_row1 01010
		cg_row2 00000 ;77h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10001
		cg_row2 01010
		cg_row1 00100
		cg_row2 01010
		cg_row1 10001
		cg_row2 00000 ;78h

		cg_row1 00000
		cg_row2 00000
		cg_row1 10001
		cg_row2 10001
		cg_row1 01010
		cg_row2 00100
		cg_row1 01000
		cg_row2 10000 ;79h

		cg_row1 00000
		cg_row2 00000
		cg_row1 11111
		cg_row2 00010
		cg_row1 00100
		cg_row2 01000
		cg_row1 11111
		cg_row2 00000 ;7Ah

		cg_row1 00110
		cg_row2 01000
		cg_row1 01000
		cg_row2 11000
		cg_row1 01000
		cg_row2 01000
		cg_row1 00110
		cg_row2 00000 ;7Bh

		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000
		cg_row1 00100
		cg_row2 00100
		cg_row1 00100
		cg_row2 00000 ;7Ch

		cg_row1 01100
		cg_row2 00010
		cg_row1 00010
		cg_row2 00011
		cg_row1 00010
		cg_row2 00010
		cg_row1 01100
		cg_row2 00000 ;7Dh

		cg_row1 00000
		cg_row2 00000
		cg_row1 01000
		cg_row2 10101
		cg_row1 00010
		cg_row2 00000
		cg_row1 00000
		cg_row2 00000 ;7Eh

		;cg_row1 11111
		;cg_row2 11111
		;cg_row1 11111
		;cg_row2 11111
		;cg_row1 11111
		;cg_row2 11111
		;cg_row1 11111
		;cg_row2 11111 ;7Fh


end


file: /Techref/scenix/lib/io/dev/video/servid_sx.htm, 67KB, , updated: 2007/3/3 04:58, local time: 2024/10/8 01:25, owner: pv-bos-KA6,
TOP NEW HELP FIND: 
44.220.184.63:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.massmind.org/techref/scenix/lib/io/dev/video/servid_sx.htm"> Peter Verkaik's port of the MASM SERVID code to the SXKey</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to www.massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .